Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BPAC1800BS1

BPAC1800BS1 KitchenAid Air Conditioner - Overview

Get Parts and Repair Help for BPAC1800BS1

If you know the air conditioner repair part you need, you can browse the list of all parts on the BPAC1800BS1, or you can search by name or part description. You can also find your part by where it is located on the BPAC1800BS1 by selecting a section below. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.79

Washer, Support

This part is located on the drum roller support shaft in your dryer appliance. The exterior of the washer is 1 inch in diameter with a hole in the middle and is made of metal. They...

$3.75

Hex Nut

This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to wear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.

$3.02

Single Hex Head Screw

Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".

$30.25

Silicone Rubber Adhesive - 2 oz

Silicone rubber adhesive is a high temperature adhesive that is used for gaskets on dryers and felt seals. It is used on many different appliances for many different application reasons. This silicone paste creates a waterproof seal between components. This product is a 2 oz. tube. Unplug your appliance if you will be working on any internal workings and applying this sealant. Wear gloves to protect your hand from accidently applying sealant to your skin. The surface must be clean, dry, and free from oil and grease. Coat one surface and let it dry for at least one minute and then bond.

$23.20

Motor Clip

$4.89

TIE-WIRE

$3.75

Screw

This screw is sold individually. Size: 8-32 x 1/4 inch.

$83.25

Thermostat with Clip and Guide

This thermostat is for residential air conditioners and is responsible for regulating temperature. The thermostat comes with the clip to attach it to your AC and a visual guide to help with the repair. If your thermostat will not cool properly, or the compressor will not switch on or off, you could have a faulty thermostat. Before you replace your thermostat, remove it from the unit and clear any dust or debris that has built up, because a buildup of dust can interfere with the reading. If the issue continues, you should replace the part. Make sure the power is disconnected to your air conditioning unit before you begin the repair.

$56.02

Air Filter

This part is sold individually. The air filter is part of your room air conditioner and prevents dirt, dust, and other debris found in the air from getting inside your home. Over t...

$28.10

SEALER

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Ac Would Cool But Compresser Would Not Cycle On &Off

  • Customer: Ron from Knob Noster, MO
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 6 of 13 people found this instruction helpful
Replaced the temp control and sensor. Controls on this unit are easy to get to and electrical connections were slide ons read more

Filter was filthy, no telling how long it had been since changed

  • Customer: SHIRLEY G. from Mabank, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 8 people found this instruction helpful
Took out old filter and replaced it with the new filter read more

Needed new Ice Maker

  • Customer: Joseph from Liberty, MS
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 4 of 9 people found this instruction helpful
Removed back cover, and installed the water valve. Removed the water supply tube cover and installed the supply tube. Opened freezer and removed the electrical cover, removed the knockouts and pulled line out. Hooked up ice maker and installed it to wall. Turned water on and waited a couple hours, it is making ice. Installing the ice maker was easy. Ru... read more