Models > BLTF2940FS0

BLTF2940FS0 Frigidaire Washer - Overview

Get Parts and Repair Help for BLTF2940FS0

If you know the washer repair part you need, you can browse the list of all parts on the BLTF2940FS0, or you can search by name or part description. You can also find your part by where it is located on the BLTF2940FS0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for BLTF2940FS0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$6.60

Door Strike

Use with front load washers.

$68.60

Door Lock and Switch Assembly

***NOTE: As per the manufacture, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require the door lock kit.

$45.43

Shock Absorber Kit

This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorou...

$49.57

Water Inlet and Dispenser Valve

This part comes with the sensor/thermistor.

$100.34

Drain Pump - 60Hz 120v

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

$169.50

Bellow Kit

Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle. ***NOTE: This part has been redesigned by the manufacturer and is interchangeable with the old design.

$5.27

SCREW

$29.11

Drain Hose

Also known as tub-to-pump drain hose.

$16.73

Spring-Held Bellow Clamp

$33.87

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Door Catch

  • Customer: Joy from Columbia MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 466 of 464 people found this instruction helpful
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done. read more

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 189 of 225 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

Old Bellow Ripped

  • Customer: Peggy from New Castle PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 130 of 176 people found this instruction helpful
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside ... read more