Models > BISB42EKB

BISB42EKB General Electric Refrigerator - Overview

Get Parts and Repair Help for BISB42EKB

If you know the refrigerator repair part you need, you can browse the list of all parts on the BISB42EKB, or you can search by name or part description. You can also find your part by where it is located on the BISB42EKB by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for BISB42EKB parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$137.62

Ice Maker

Replacement icemaker kit - electronic. This kit includes a 4 pin round plug-in connector, 6 post plug-in connector, tube and fill cup.

$33.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push them into new valve. To remove - depress ring that the tube slides into.

$20.09

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$11.93

Package of 12 Screws

$5.79

Water Tube Union - 5/16" x 5/16"

Sold individually.

$136.36

Auger and Ice Bucket Assembly

This auger and bucket assembly is used on 25 cubic feet and 27 cubic feet side by side models.

$59.37

Solenoid and Arm Assembly - 120V 60Hz

This solenoid and arm assembly is for the cube/crushed ice.

$47.63

Defrost Timer

This refrigerator defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are internal, and the label is orange.

$10.25

Ice Dispensing Drive Cup

Found at the end of the auger in the ice container - replace when the icemaker doesn't dispense ice.

$18.16

Ice Bucket - White

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 173 of 190 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

No power to the fan and compressor

  • Customer: Christian from Kearneysville WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 83 of 113 people found this instruction helpful
I have a fridge in my garage. I have found that a glass of ice water or a cold drink outside is very important to me. When I discovered melting ice dripping onto the garage floor I was very upset. I spun the fridge and found that the compressor and fan weren't starting. I got out my multi-meter and discovered that power was not making it to these compon... read more

The oiginal Ice Bucket auger became rusty and discoloered the ice.

  • Customer: Michael from Antioch CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 41 of 47 people found this instruction helpful
I went on line to find the part. Luckily I found PartSelect.com. All I had to do was enter the model number into the search box and scroll through the list of parts.
I ordered the part over the weekend and recieved it on Tuesday!
All I had to do was remove 4 screws from the original Ice Bucket and attach the new one.
Perfect fit in under 15 mi... read more