BGHD2433KF0 Frigidaire Dishwasher - Instructions

Broken friction cable on the right hand side. Remove screws that hold dishwasher to cabinet, pull out the dishwasher far enough to get to the friction cable and rear spring. Remove broken cable. Attach new cable to rear spring and connect to door hinge. Push back dishwasher and screw in the two screws that keep the dishwasher attached to the cabinet. Very simple.

Pulled out old gasket from bottom of door with needle nosed pliers and then put in new one in.

Unscrewed the old spray arm and replace with the new spray arm.

The best part was in the ordering process. Having the diagrams with the parts let me see that I was ordering the correct part. Thanks!

Unscrewed upper sprayer by hand, screwed new one in by hand. Piece of cake!

The spray arm comes off into 3 parts but is really only supposed to be one. I removed the nut from the old assembly and attempted to place the new assembly on by hand. The new nut seemed to be slightly smaller than the original so it would not attach to the dishwasher. Using a kitchen knife, I removed the new nut from the arm unit and attached the new arm to the original nut and it went back on easily. The connection of the new arm to the new nut was 3 tabs that needed to be depressed with the knife and was a different conection method than the assembly that kept coming off in the wash cycle. The replacement part had a much better design than the original.

I replaced the basket. No tools necessary. New basket seems sturdier than original. Very satisfied with my purchase.

Unscrewed dishwasher from cabinet and pulled out about 1 foot. Took bottom plate off of dishwasher. Undid clamp on hose of discharge of inlet water valve and removed hose. Shut off water to water inlet valve and removed. Took wiring clip off of water inlet valve. Removed 2 screws holding water inlet valve in place. Installed new water inlet valve in reverse order.

Discovered upper wash arm had come off. It looked like it was repairable, but the bushing/clip holding the arm came off after one wash. Looked on line and reviewed part and saw it was a one piece assembly from photos. Removed old assembly by unscrewing from top of washer and screwed new assembly in place.

Fully open dishwasher door to horizontal position, remove lower dishwasher rack and relocate to another temp location, grab old lower door seal from right or left corner and pull completely out of door, lay the old bottom seal aside facing the same direction as once installed (seal has a notched side which faces the right side of door), match direction of the new seal with the old seal (match the notched side of seal to the right side of door), gently push the seal into the door starting on the right side (notched side of seal fits tightly into a receiving area inside the door), and finally push the remaining portion of the seal into door (aligning with the right side already properly seated inside dishwasher door). Close dishwasher and run water cycle to confirm leak.

I was able to pull out the top basket were the glasses are put then I lined up the back and the center plastic clip an slid on the center spray arm. It took about 2 miniutes

First thing I did was turn off the power to the dishwasher, then remove the racks. Remove the foot plates, remove the two top screws holding the dishwasher. Then using the socket set, retract the two foot stands to pull the dishwasher forward. You may not have to do this step as I had to get it over tile. The pully springs are on the sides, easily replaced. After replacing the springs and I recommend replacing both at the same time, put everything back. The hardest part will be the foot plates, there are two and getting them lined up and the screws back in is a bit of a challenge. Then you are done.

tossed the old one a replaced with a new.Hardest 10 second repair ever....It took 10 seconds had to open and close the door.

The Parts finder was the big help. After that all that was needed was to loosen the clamps and replace the old hose with the new one A piece of cake. Slide the washer back into place and replace the screws that hold it to the counter. Out and back in, 30min. top end to complet the job

New one snaps into place easily.

Unsnapped three clips in lower rack securing old fence in rack. Attached clips to new fence and snapped assembly back into rack.