Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BGHD2433KB1 > Parts

BGHD2433KB1 Frigidaire Dishwasher - Parts

All parts for the Frigidaire Dishwasher BGHD2433KB1

Below is a list of all parts for the Frigidaire Dishwasher BGHD2433KB1. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the BGHD2433KB1
1-14 of 119
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$14.92

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$26.08

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$3.63

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the heating element nut. Replacing the nut is an easy job, does not require any specialty tools, and should not take you more than 10 minutes. For our step by step guide, click the video below. The brass nut measures 7 inches in length x 1 inch in width x 5 inches in height, and fits most dishwashers. To see if this part is compatible with your dishwasher, check the list of compatible brands below.

$19.51

HOSE

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in pr...

$20.74

Pulley Spring

Sold individually.

$18.60

Splash Shield Kit

This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If...

$74.72

Upper Rack Assembly - T3 PRO

This is the complete upper rack and the wash arm.

$20.74

Friction Door Cable

Sold individually.

$56.30

Drain Pump -120V 60Hz

The drain pump ejects the water from the dishwasher.

$34.50

Delivery Tube Gasket

Sold individually.

$19.65

Lower Rack Wheel with Clip

Sold individually. Order quantity required.

$59.17

Lower Dishrack Assembly

This lower dishrack assembly comes with 8 rollers enabling it to roll in and out with ease. The dishrack is approximately 22 inches long x 20 inches wide. The dishrack holds dishes...

$40.69

Heating Element

This dishwasher heating element is not designed to heat the water that enters it, but is designed to maintain the heat of the water that enters the dishwasher. It is located on the bottom of the dishwasher. NOTE: Brass nuts are NOT included. Must be ordered separately.

All Parts for the BGHD2433KB1
1-14 of 119