BDNT22L9K Refrigerator - Instructions

just had to remove the fan motor the hard thing is getting down to it

Removed malfunctioning icemaker and discovered that inlet water line was frozen. Thawed line using hairdryer and problem resolved. Returned new icemaker to PartSelect they promptly credited my credit card account. Problem solved.

I discovered that the water inlet was freezing, then the incoming water would run into the tray. I watched the video, then removed the ice maker. I discovered the the top two screwed just had to be loosened, not removed. I removed the bottom screw and move the ice maker to the side to disconnect the wiring harness. I found it to hard to disconnect. The pinch clips did not depress as they were supposed to, but the finally release. I did the replace without unplugging the refrigerator and it went fine. Took less than 15 minutes.

removed the old tank replaced with new tank I had to cut the end of each water line to make it fit into the fitting. check for leaks. It is good to run a bit of water through the tank to get out the air

I removed and inspected the old unit and found the tray coating was flaking off. I ordered the new ice maker on line, One screw and rotate unit counter clockwise about 10 degrees unlocked it from the two snap in mounts. then unplugged the wire harness and it was free. Had to put the short wire harness on new unit, reverse removal steps and it is completed and working fine.

The video of the repair is a helpful guide, but my refrigerator has the compressor very close to the condenser fan motor. With the compressor comes the copper tubing that is all in the way. I had to carefully bend them now and then to allow me to get my hands in position. The how to is easy, but the working with tools in cramped quarters was difficult. I think my Maytag side by side model makes for this job to be difficult, maybe yours may not be so bad. I took a couple of hours to complete. After the first hour, I covered the bare wires, and plugged the frig back in so it could do some cooling. I placed a small in front on the condenser to blow across it. Had a little break, then finished the job.

I unpluged the refrig, removed the shelves and the back panel on the freezer side of the unit. This exposed the fan motor and fan blade. I removed two screws holding the fan unit in place, unpluged the wires connecting the fan unit to power, and then removed two other screws securing the fan motor to the bracket. I removed the fan motor blade from the old unit and installed it on the new fam motor. I replaced the fan unit into the bracket, pluged the wires back into the fan motor and secured the motor to the refrig. Replaced the back panel and shelves, pluged the refrig into the wall.....easy.

Had to replace ice bucket rack because auger motor broke the plastic backing and also the auger motor because shaft was bent on old auger motor. Just followed directions on web site to do repair.

Ordered the correct replacement part (Icemaker Auger and Crusher Blade Assembly) as found here at PartSelect.com. Part was delivered within two days. Removed two screws to remove the old assembly; inserted new assembly, replaced the screws and problem fixed. Couldn't be easier.

Removed old auger unit by removing two screws - installed new auger unit by replacing the two screws. Easy schmeasy!

Based on comments I read at this web site, I first ordered the water valve; that did not fix the problem. Replacing the icemaker did fix the problem. It was easy to replace. Contrary to the instructional video, I couldn't simply tilt out the icemaker at the bottom after removing the lower screww; I had to loosed the two top screws as well. The leak was caused the coating on the icemaker being cracked and peeling.

I watched the video which gave me confidence that I could do the repair which I did in very little time. One thing to emphasize though: When you remove the vertical wire connector from the back of the freezer compartment, remember which color wire is on the top. I needed to watch the repair video a second time to be able to make that determination. Probably the repair video should have mentioned keeping track of that connector regarding the re-connection of it because it could also connect when turned 180 degrees.

I watched a youtube video and completed the repair in less than an hour from start to finish and save myself a service charge. It was fairly easy, the only problem was that it was a bottom freezer and getting to the ice maker was harder than if it was a side by side or top freezer.

I have an Amana freeze and I followed the procedure in the video. Which is very good! However on the Amana Model there two slight differences in the procedure that I felt I needed to do. The first one is, the condenser fan bracket is attached to the Freezer chassis with 4 screws, not three. The removal and installation of the back screw by the fan is a bear. I removed the other three and it allowed me to rotate the fan slightly to get more access to the fourth and did same on installation by just starting the 4th screw and then tightening it later. The second issue was my new fan hit the housing when I spun the fan. When I looked at the old one. It had a phenolic washer, between the fan and motor which spaces the fan out about a washer thickness from the motor. When I tried to remove the old one it broke in four pieces due to age. So, I made my own with a washer that I super glued to the motor housing after carefully centering it on and clearing the motor shaft . Seemed to work with out any more noise or balance issues...Thanks, your delivery was blindly fast and video was great!

I used the video on your website. It made me feel very satisfied that I was able to do it myself!