Models > BDNT22J9 Maytag

BDNT22J9 (8B15A) Maytag Refrigerator - Overview

Get Parts and Repair Help for BDNT22J9

If you know the refrigerator repair part you need, you can browse the list of all parts on the BDNT22J9, or you can search by name or part description. You can also find your part by where it is located on the BDNT22J9 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for BDNT22J9 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$37.17

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air cooling for the condenser coil.

$2.70

Screw

This screw is sold individually.

$3.17

Light Bulb - 7W

Sold individually. This bulb is a 7 watt appliance incandescent light bulb.

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$2.70

SCREW

Sold individually.

$2.70

Screw

This is screw is sold individually.

$3.56

Plastic Tubing

1/4" Plastic tubing, 8 1/2 feet long.

$2.70

Inlet Hose Gasket

$3.96

Compression Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 103 of 111 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 86 of 89 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 17 of 20 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more