Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BDNT22E9H

BDNT22E9H (4B64A) Admiral Refrigerator - Overview

Get Parts and Repair Help for BDNT22E9H

If you know the refrigerator repair part you need, you can browse the list of all parts on the BDNT22E9H, or you can search by name or part description. You can also find your part by where it is located on the BDNT22E9H by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for BDNT22E9H parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$40.25

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a mounting nut for the blade and a cushion. This part provides forc...

Order within the next 11 hrs and your part ships today!
$2.80

Screw

This is screw is sold individually.

Order within the next 11 hrs and your part ships today!
$107.75

Ice Bucket Auger Drive Motor Kit

This motor kit comes with a thermally protected motor, a washer and a mounting bracket. The motor performs eighteen revolutions per minute, carries 115 volts, and drives the auger ...

Order within the next 11 hrs and your part ships today!
$8.01

Compression Nut - 5/16"

Order within the next 11 hrs and your part ships today!

Water Tank Kit with Unions

$237.79

Complete Ice Maker Kit

This kit comes with ducts, a water fill tube, and the hardware needed to install the icemaker. It replaces the old twist-tray style of icemaker.

Order within the next 11 hrs and your part ships today!
$20.55

Ice and Water Actuator Switch

This ice and water actuator switch is an inch long. It is black on one side and white on the other. This switch is made of plastic and has two metal prongs extending from its body.

Order within the next 11 hrs and your part ships today!
$2.80

Screw

Sold Individually.

Order within the next 11 hrs and your part ships today!
$20.98

Drive Shaft Clip

This drive shaft clip is less than an inch long. It is all white in color and is made of plastic. This clip is used with the drive shaft of the ice cube tray.

Order within the next 11 hrs and your part ships today!

Auger Impeller

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Sometimes the condenser fan would start causing the refrigerator to overheat.

  • Customer: Tom from Franklin, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 124 of 132 people found this instruction helpful
Unplug the appliance.
Removed the screws holding the back panel.
Removed the fan blade.
removed 3 screws holding the condenser fan.
Remove the 3 metal brackets attached to the fan.
(First note which studs the brackets are attached to. Attach the 3 metal brackets to the new fan. (New screws were supplied)
Cut and strip the wire a... read more

noisy fan motor

  • Customer: robert from nashotah, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Socket set
  • 24 of 27 people found this instruction helpful
rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, close up, reverse pan... read more

Refrigerator stopped cooling. Pulled it out of the alcove and plugged it back in. Compressor starfted but noticed condenser fan was not turning. Unplugged fridge and tried to turn the fan by hand - frozen.

  • Customer: Florentino from Windsor Locks, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 19 of 25 people found this instruction helpful
Remove the back hardboard cover screws for access to the condenser fan. I opted to tip the fridge over on its side for even better access to the fan mounts and wire. Replaced the fan assy (reused the fan). Splice the wire and it's done. read more