Models
>
BDG7600
BDG7600 Maytag Dryer - Overview
Sections of the BDG7600
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Screw, 8/18 x 3/8
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$5.42
In Stock
Thermal Fuse (Limit: 183)
PartSelect #: PS11740678
Manufacturer #: WP306604
This thermal fuse mounts on your dryer's blower wheel housing. It will cut out once your dryer's internal temperature reaches 183 degrees Fahrenheit, and will not cut in again. Like a house fuse, you ...
$31.26
In Stock
Multi-Temperature Gas Thermostat
PartSelect #: PS11740685
Manufacturer #: WP307250
Also known as cycling thermostat with internal bias heater - L150-25 - 5 terminal.
$72.15
In Stock
Questions And Answers for BDG7600
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The dryer would run continuously when in auto
I removed the two screws on the front of the dryer and pulled out the bottom of the dryer front until the clips on the top came loose. Next I removed the two screws that hold the thermostat in place and then switched the wires from the old one to the new one. I did them one at a time to ensure that they didn't get mixed up. After that
... Read more
I reinstalled the thermostat and then replaced the front of the dryer. The timer now advances when it is in auto mode.
Read less
Parts Used:
-
Patrick from Marysville, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
18 of 18 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was getting really hot in normal drying mode
This is a gas dryer. I was able to access the thermostat through the small front access panel. Not easy to see but with a short nut driver I could take out the two screws. I was able to pull the thermostat to the front panel hole and switch the wires. Putting it back in was a challange since I had to do it by feel since I could not lo
... Read more
ok and get my arm in at the same time. Suggest anyone that does this put a small piece of paper around the screw to hold it in the driver
Read less
Parts Used:
-
Green from Germantown, TN
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
7 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No flame
Firts replaced a thermostate - did not fix the proble. ( had a glow from the starter but no flame.)
checked igniter sensor OK (got no resistance) so replaced the two coils that sit on top of the gas burner. With new coils noticed a much brighter glow from the igniter and the gas line opened up to produce a flame
D ... Read more ryer has workd successfully for the last 5 loads.
Able to run dryer with the front removed by holding in the microswitch activated when door is closed.
checked igniter sensor OK (got no resistance) so replaced the two coils that sit on top of the gas burner. With new coils noticed a much brighter glow from the igniter and the gas line opened up to produce a flame
D ... Read more ryer has workd successfully for the last 5 loads.
Able to run dryer with the front removed by holding in the microswitch activated when door is closed.
Read less
Parts Used:
-
Christopher from Toms River, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!