Models > BCS42ELD

BCS42ELD General Electric Refrigerator - Overview

Get Parts and Repair Help for BCS42ELD

If you know the refrigerator repair part you need, you can browse the list of all parts on the BCS42ELD, or you can search by name or part description. You can also find your part by where it is located on the BCS42ELD by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for BCS42ELD parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the BCS42ELD [Viewing 1 of 1]

$33.30

Dual Inlet Water Valve

This valve comes with 1/4" compression inlet. NOTE: This part comes with new quick connections. To install - cut retaining nuts off of existing plastic water lines and gently push...

$20.09

Run Capacitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$47.63

Defrost Timer

This refrigerator defrost timer will cycle for twenty-five minutes after every six hours of run time. The timer itself is made of plastic, and its terminals are bent, the leads are...

$137.62

Condenser Fan Motor - 115V

This part comes with 3 round pin connection terminals. This fan motor circulates the air through the refrigerator grille and cools the compressor and condenser coils. It also helps to evaporate extra water in the drain pan.

$3.62

Plastic Tube - 1/4"

$131.36

Evaporator Fan Motor - Harness NOT Included

This evaporator fan motor operates in a counter clockwise fashion. This motor's shaft is 3/8 of an inch and the motor has two right side terminals. NOTE: Harness wires NO longer comes with the part.

$2.48

Grommet - Black

Sold Individually.

$12.82

Power Cord

$31.58

OVERLOAD

$24.98

Drawer Slide Rail - Right Side

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cracked housing on the vaave

  • Customer: anthony from thornton CO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 179 of 196 people found this instruction helpful
1. Turn off water supply, and electrical ( unplug it) to fridge.
2. Remove water line to valve. Watch for water to pour out of the line. Have a towel handy.
3. Remove the cardboard cover on the bottom of the fridge.
4. Remove the screws that hold the valve in place.
5. Remove the valve, be careful the waterlines are still attached.read more

display showed dE

  • Customer: Nancy from Hamburg NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 37 of 61 people found this instruction helpful
popped off front grille, removed 2 screws for bracket, then had to remove one screw for timer. unplugged old timer, reversed procedure, all works. read more

refrigerator was not cooling but the freezer worked fine.

  • Customer: Wanda from Cabins WV
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 20 of 24 people found this instruction helpful
My husband put on the defrost timer. At first I thought the part was not going to fix the problem. After about 5 hours my refrigerator was still warm. I went to work and when I got home that evening my refrigerator was cooling and down to 28 degrees. So if you replace this part wait at least 12-24 hours. Give it time to stablize. My husband says it h... read more