BCRG860A Maytag Range - Instructions

Undid screws on front and some on the back and replaced part and put screws back on and it fixed the proble

The only difficulty with following the supplied video, is that my ignitor did not come out as easily as a few turns of the screwdriver. The screws stripped as I tried to remove them, making them twirl in their holes. I had to apply back pressure for them to come off and free the ignitor for replacement. Other than that, the installation went smoothly, and the oven sprang to life within 10 seconds of turning it on.

I simply followed the "general" instructions from the online video "Partselect" provides and perused the instructions included in the kit. The OEM igniter was much longer than the replacement but the new part was spec'd just fine. It was necessary for me to open up the back of the stove in order to retrofit the igniter leads to the original block connector and install the heat resistant padding included in the kit. The additional necessary hardware fit very nicely inside the oven. The stove's oven fired up without any problems and spared me the expense of purchasing a new oven. Thank you very much "Partselect".

I removed and replaced the igniter. I described these symptoms on the web site and it detailed that90% of the time by installing a new igniter it will fix the described problem. So I ordered the part and installed the part and everything worked OK. The only tool I had to use was a screw driver to remove three screws. It took about half an hour. If I had to do it again it would take about 15 minutes.

Unplugged oven. Removed door,racks,and bottom shelf. Removed screws from ignitor and unplugged it from connection. Installed new ignitor with screws and plugged in to connection. Tucked wires behind insulation as they were before. Installed previously mentioned items and turned on to check. Worked great and am very pleased with PartSelect and the assistance they offer.

Slid oven out from counters. On each side there are 3 screws on the front and three screws on the back holding the side piece on. Once off, the spring was very easy to get at and replace. I had only one broken, but replaced both anyways. I think it took longer to clean the sides of the oven that haven't been touched in years than to replace the springs. This job was very simple and easy.

Ordered oven Igniter kit PS1573892 which cost $73.00. Received the kit with instructions easy to follow to install. I was surprised how easy it was to repair, with the help of my wife we did the job in about 2 hours, the oven now works great. I really saved a bundle of money doing this myself, a local repair service wanted $114.00 for the same part and $200.00 labor to install and this is the gospel truth. I am 96 years old. RMA Bluefield, WV

Take off oven door, remove racks, lift out bottom plate of oven, remove deflector shield, unbolt old igniter gently fish out the wire and plug from the back of the oven. Unplug and replace with the new igniter. re-assemble oven.

Followed the directions on the video. Very easy to do.

The burner head caps on my Magic Chef no longer work and had to be replaced. I ordered 1 of the 4 caps to see how it would work out for me. I did not have any issues replace the cap. I contacted PartSelect and order the other 3 caps. The sales representative took my order and was EXTREMELY helpful. Now I know why all of my neighbors choose PartSelect. Including the cleaning, it did not take me more than 15 minutes. The video was also extremely helpful. Our Magic Chef should be good for another 6-8 years. Thanks PartSelect.

I had to pull the range out from the wall and loosen the rear cover to free the connector for the sensor as it got stuck on a corner guide. Put the new sensor in, rear cover back on, range back in place and tested the oven. Oven heats fast now and keeps a more even temp. Makes me wonder how long I was trying to cook with a bad sensor.

turn burner cap counter clock wise lift out remove to leads,do not have to turn power off they are mini volts.Insert the two (leads)weirs on to new cap,twist back in done.Fire it up.

took oven door off easy just lift up took bottom tray to oven out took bottom draw of stove out removed tin panel cover 2 screws to unplug igniter took 2 screws out of igniter and pulled unpluged wire through insulation. installed new igniter 2 new screws put wire through insulation and pluged it in. The only thing to check is matching the plug ends correctly before pushing them together.

Basic instructions provided were accurate. Most difficult part was bending down and reaching across the oven door. A general information note would have been helpful. The circuit that feeds the igniter and the gas valve is a series circuit. So, even though the igniter was glowing cherry red, the igniter was still the cause of the gas not flowing, The voltage drop across the igniter was larger then normal causing the voltage to the gas valve to go down and to be insufficient to allow the gas to flow.

After watching your do-it yerself video, I turned off the gas and unpluged ac power cord, I removed the stove door and then removed the bottom tray inside the stove unscrewed tray plate pulled buner out of its housing. I then unscrewed the two screws to the old ignitor and unpluged it. Pluged in the new one screwed it to the burner bracket, put everything back togher then tuned on the stove. IT WORKS!!