BCRG860 Maytag Range - Instructions

first of all i have one advantage even though i am 70 yrs old i had a appliance shop for sears in the 60s and 70s and have not forgotten to much of the basics i am still in the security business and up on electronics. last time i had the company repair the oven , 70 dollars for the part 75 dollars for the svs call. (first igniter was on full warranty) well this time i decided to look for trhe part myself, i just went on line typed in oven repair parts and eventually all these sites came up. yours was the most professional looking and i took a chance. guess what everything you promised you delivered. price quality USA made parts and delivered in three days . opened package went to work less than fifteen minutes back in business.
will sure use you again if the need arises thank you

Pulled off the oven door, just lift straight up. Pulled out the floor of the oven, very easy just lift from the back. The only problem I had was the screws holding the old igniter wouldn't come out, they just spun. I snipped them off and picked up two new ones at the hardware store. Pull the wiring harness in through the hole in the back of the oven. Unsnap old wiring harness, snap in new one. Reattach the new igniter, replace floor, replace door. Turn on oven and cook food... fairly easy repair.

Pulled the stove out from the wall. Removed the left side of the stove. Removed the wires from the old igniter. Modified four of the wire ends with the proper size spade connectors (supplied with the new part). Reinstalled the wires onto the new part. Tested the burners. Reinstalled the stove side. Moved the stove back into position.

Pulled the oven away from wall to access rear of oven. Disconnect electric plug from duplex outlet, turn off gas supply ball valve. Removed two screws that retain sensor on inside of oven. Disconnected two prong sensor connector at rear of oven. Tied a length of string to sensor connector wires. Pulled old sensor out through front of oven. Use the string to tie onto new sensor connector wires and pull new sensor into place from rear of oven. Retain sensor with two screws. At back of oven, used connector jumper supplied with part package to make connection to existing connector.

The old gasket fell apart as I replaced the oven light and had to be replaced. That was very easy once I received the part. The spring broke on the oven door and had to be replaced. I initially tried to reach in from inside the pan drawer under the oven. That was impossible to reaach but it only took a few minutes to realize that I had to remove the side panel. I had to slide the range out from between the cabinets, but once that was done it was a relatively easy fix, without any special tools needed.

I first removed the bottom of the oven and the flame guide to uncover the igniter assembly. Then I applied WD40 to the two Philip head screws and unscrewed them to release the old igniter. The two wire leads from the igniter went into the back of the oven and I could not reach the connection block. So I pulled the oven out far enough to get behind it and took off the panel covering the electrical wires in back. I had previously disconnected the electrical cord from the wall outlet. After I determined that I could not remove the connection block I returned to the igniter and cut the two existing wires close to the ceramic igniter assembly. I marked the top wire with a Sharpie pen so that I would not mix up the new leads when I install the new igniter. Although it was awkward to work inside the small oven space I was able to strip the insulation back about 1/2 inch and then connect the new igniter wires using the twist caps supplied with the kit. I pushed the wires back into the space and added the insulating material supplied. The igniter assembly was then installed with the original two screws and the other oven covers and flame guide reinstalled easily. After reconnecting the power outlet the oven was back in operation with ignition of gas flame within a minute or so. It was a good feeling and now we do not need to consider replacing the gas range.

Range is 20+ year old 'condo issue' and difficult to pull from wall since previous owner had tiled it in. Going in from the back was going to be a pain.
Removed the oven door by opening slightly and pulling up. Removed grilles. Removed bottom of oven by sliding 2 latches in the back forward and pulling it up. Removed 2 screws holding igniter (long-style) to the rear of the burner. Cut power to the range and snipped the 2 igniter wires as close to the igniter as possible, leaving me only about 1 inch of wire to work with. Removed 2 screws holding old plate to rear of the back of the interior of the oven. Snipped off the connector on the new igniter. Carefully stripped about 3/8" of insulation off of all wires and used hemostat to hold wires together while applying the wire nuts. Used hemostat to work the wire nuts and excess wire back into the hole. Stuffed the hole with supplied insulation. Attached new back plate with original screws and attached igniter to burner with original screws. Reapplied power to range and did a test light. It worked, so I reassembled the rest. For me, the worst part was holding the wires together so the wire nuts would 'take', while working inside of the oven. But, an easy and successful job!

Look in the oven. On the upper left corner is the sensor. Remove two screws. Gently pull the wire and connector through the hole and insulation. Disconnect old sensor, replace new. Gently push the connection through, then finish pulling through from behind the stove. Replace the screws inside the oven. Done.

Removed the two screws that hold the back glass in place. Rotated old bulb out of it's lamp fixture and replaced it with the new bulb. Replaced glass and reinstalled the screws.
The hardest part was finding the bulb ... a very unique 18W flourescent. I wasted a couple of hours trying to locate it locally at my regular suppliers. The order at PatsSelect was easy and direct and the bulb was on my doorstep 3 days later .. an exact fit. Thanks guys.

unscrewed old burner head ;disconnected 2 wires; repaced with new burner head and replaced wires. Unfortunately, before we really needed to replace the other burner heads, the cooktop itself developed a gas leak. We decided to replace the whole thing, and therefore would like to return the unboxed, unused 4 remaining burner heads.

Purchased 2 piece broiler pan from this site

Pulled the stove out, removed the sides and attatched the new springs( replaced both while the stove was out). Worked like new and put the stove back.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I then conected the new element and replaced te two screws. Turned on the oven & works fine.
Very Easy!

removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) pushed wires back in and secured sensor