Quick Question!

Have you ever purchased from PartSelect.com before?

Models > BBBD2432KW0

BBBD2432KW0 Frigidaire Dishwasher - Overview

Get Parts and Repair Help for BBBD2432KW0

If you know the dishwasher repair part you need, you can browse the list of all parts on the BBBD2432KW0, or you can search by name or part description. You can also find your part by where it is located on the BBBD2432KW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for BBBD2432KW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$10.15

Bottom Door Gasket

This gasket is found at the bottom of the dishwasher door and helps prevent water from leaking from the bottom edge of the dishwasher door. If your dishwasher is leaking water from...

$15.36

Tub Gasket - Gray

This dishwasher door gasket creates a seal around the dishwasher to ensure that water is not able to leak out. If this was not in place there would be a gap between the opening of the dishwasher tub and the outside of the door. If this has torn, you might notice leaking water coming from your dishwasher or the inability to shut the door properly. Simply pull out the current gasket, ensure the area is clean, look for the indicator on your new gasket to determine the middle, and press into place without stretching the material. After the repair is complete, shut the dishwasher door and leave closed a few hours to ensure it properly seals into place.

$26.85

Water Inlet Valve - 120V 60Hz

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner of the dishwasher. The attaching solenoids on the valve open and close ...

$29.77

Lower Spray Arm with Shields

This lower wash arm is located in the bottom of the dishwasher. The spray arm of this part rotates to spray water inside the dishwasher tub to clean dishes. If your dishes are not getting cleaned properly or your dishwasher is making unusual noises and leaking water, replacing this part can fix the problem. To repair, first open the dishwasher door and pull out the lower rack. Next, remove the lower wash arm by flex out tabs to release it. Now you can replace new lower wash arm by lining it up and pushing down to lock it in place. Pro tip: make sure to spin it around a bit to make sure it works. Refer to the manual provided by the manufacturer for further installation instructions. Make sure to unplug your appliance from the power source before beginning this installation.

$3.73

Heating Element Brass Nut

The heating element nut is used to connect the heating element to the dishwasher tub. If water is leaking from underneath your dishwasher, you may need to tighten or replace the he...

$19.45

HOSE

If your dishwasher is leaking or not draining properly, you may need to replace the drain hose. The drain hose connects to the pump located below the lower spray arm and aids in proper dishwasher drainage. This white and black plastic hose is 7.5 feet long. For this repair, you will need either a 1/4-inch or 5/16-inch nut driver, depending on your model. You will need to remove the lower access panel on your dishwasher to complete this repair; it is often easier to remove the dishwasher from the cabinet to do so. Be sure to disconnect the dishwasher from both the power and water supply before completing this repair.

$20.37

Door Spring

This door spring is manufactured for a dishwasher door. The door spring applies tension to the dishwasher door so that the door does not drop too quickly when it is opening. If the...

$19.25

Splash Shield Kit

This splash shield kit is used in dishwashers and is attached to the lower front corners of the tub. The splash shield is used to prevent water from spraying past the door seal. If your dishwasher is leaking from the corners of the door gasket, replace this part. For this repair, the only tool needed is a flathead screwdriver. The measurements of this part are: 1.50 inches in length, 0.50 inches in width, 1.70 inches in height. It weighs 0.10 pounds. Remember to unplug your appliance from the power source as a safety precaution.

$76.88

Upper Rack Assembly - T3 PRO

This is the complete upper rack and the wash arm.

$58.11

Drain Pump -120V 60Hz

The drain pump ejects the water from the dishwasher.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The spray arm would fall off during the washing cycle.

  • Customer: Roy from Worcester, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 709 of 716 people found this instruction helpful
Repair was simple. I unscrewed the old grommet which held the old spray arm and screwed-on the new one. About 30 seconds was required. Other people having this problem should note that the spray-arm is made of three pieces which are inseparable when the arm is new. The arm is sold in this form. However, when your machine is having the problem that the a... read more

Bottom Door Seal fell apart and started leaking.

  • Customer: Scott from Flowood, MS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 239 of 270 people found this instruction helpful
First I opened the door all the way. Second I reached down to the bottom gasket then grabed it on the right end of the seal that is on the right side of the door. Then I pulled the end outward from the bottom of the door toward the heater coil in the bottom of the washer. It came out real easy. You see it just snaps into a little plastic groove under the doo... read more

Leak in the water inlet valve/solinoid

  • Customer: Mickey from Ooltewah, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 142 of 155 people found this instruction helpful
1. Shut off water supply.
2. Removed inlet water hose where it connects to the vavle assembly.
3. Removed the two bracket screws holding the assembly to the frame, and detached the electrical connection from the solinoid.
4. Removed the inlet hose adapter connection from old valve and installed into new valve.
5. Attached electrical con... read more