Models > BAQG7077KW0

BAQG7077KW0 Frigidaire Dryer - Overview

Get Parts and Repair Help for BAQG7077KW0

If you know the dryer repair part you need, you can browse the list of all parts on the BAQG7077KW0, or you can search by name or part description. You can also find your part by where it is located on the BAQG7077KW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dryer. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$25.18

Door Catch

This part helps keep the door closed while the machine is running.

Order within the next 5 hrs and your part ships today!
$16.61

'M' Series Ignition Coil Kit

This ignition coil kit contains two coils. One is a two wire secondary coil, while the other is a three wire booster coil. Both should be used together in your gas clothes dryer.

Order within the next 5 hrs and your part ships today!
$68.33

Blower Housing with Blower Wheel

Order within the next 5 hrs and your part ships today!
$7.32

Door Strike

"Male" piece of a dryer door closing mechanism.

Order within the next 5 hrs and your part ships today!
$24.55

Control Thermistor

This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating. This part is located in the blower housing.

Order within the next 5 hrs and your part ships today!
$5.50

SCREW

Order within the next 5 hrs and your part ships today!
$26.06

Flame Sensor

This part senses the flame for heat allowing the gas valve to open.

Order within the next 5 hrs and your part ships today!
$26.46

High Temperature Adhesive

Used for installing felt and rubber seals on dryers.

Order within the next 5 hrs and your part ships today!
$2.95

Screw

This screw is sold individually.

Order within the next 5 hrs and your part ships today!
$13.46

LIMITER

Order within the next 5 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer would heat initially then cool down

  • Customer: Brett from Monticello MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 55 of 61 people found this instruction helpful
The top of the dryer was easily removed by prying the front up with a screwdriver then tipping it back and off of the mounting brackets. Then the front of the dryer was removed by unscrewing a single screw on each side that held the front to the side panels then pulling the front away from the dryer. Once the front was off, the coils were easily accessible... read more

Dryer would heat only on the initial start. Burner would not light again until completely cooled down. The ignitor would energize, but no gas would flow for ignition.

  • Customer: Bruce from Burnsville MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 33 people found this instruction helpful
1. Pry Dryer top up and off the clips. (Front of Dryer)
2. Remove 2 phillips screws on the inside of front panel.
3. Lift front panel up and set off to the side
4. Removed 2 phillips screws with short handled phillips driver that hold the gas valve coil bracket in place.
5. Unplugged and removed both coils, installed new coils and bra... read more

DOOR LATCH & DOOR STRIKE BROKEN ON DRYER

  • Customer: Bruce from Seminole FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 22 of 31 people found this instruction helpful
I REMOVED THE BROKEN DOOR LATCH & STRIKE WITH PLIERS. THEN I PUSHED THE NEW PARTS INTO PLACE read more