B9458B0 Roper Wall Oven - Instructions

First, turn off the breaker to the oven, then turn off the service disconnect to the whoe house. I play safe.) Open the door, pull out the oven racks to allow space. Using a Phillips screw driver, unscrew the screws near the front of the oven to loosen the element. Using both hands, pull the element straight out of the holes in the back of the oven, where you will find electric wires attached to them. Pull the ends of the element off the wire connectors. Throw it away. Get you new element, attach the element ends to the connectors. Raise it up to the top of the oven and screw the screws back in to the holes in the top of the oven. You are finished. (The only reason this took me 30 minutes is because I am an old 79 year old granny and can't bend so well, or see so well. I had to use a little acrylic paint on my finger tips to mark the screw holes, it was taking too long to find them the old way, by feel.) GG

Four screws hold the broiler element. I removed the two at the top, then removed the two screwed to the back keeping the element in place. I slowly pulled the element forward and used alligator clips to keep the wire connectors from falling back behind the oven. I disconnected the wires from the broken element and replaced it with the new element. I removed the alligator clips. I screwed the two screws on the back and the two on top and I was finished. Problem solved.

Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!

The element comes with the element attached to the bracket that holds it in place in the top of the oven. I had removed the 2 screws-one on each side--on the old element and disconnected the spade connections on the wiring after I pulled the element out far enough to expose them. I then reconnected the new element, pushed it back into place and re-installed the screws that hold it in place. A pretty simple job but I got a tremendous feeling of accomplishment after it was done. Saved a bunch of $$$ also!!

Sensor matched perfect, but had to pull large upper rear panel to find location. From there took a few minutes to reassemble back. Did not un hook gas but turned it off. Obviously unplugged power. Oven works fine.

I took the back plate off of the oven by removing 3 screws and removed a single screw holding the sensor element in place, plugged the electrical 2 prong terminals back together and re-assembled the back of the oven. After the installation was completed we did a test run. It worked for aprox. 15 minutes and shut off again. It must have re-booted its self, cause when we tried it again it worked and still is working.

The Temperature Sensor was actually installed from the back of the oven. I had to remove about six(6) screws to remove a metal panel on the back of the stove. The connector the Temp sensor came with did not match the existing connector however it did come with wire nuts as an alternative. I cut the wires and connected them with the wire nuts and replaced the pannel. Very easy fix and my 13 year old oven still runs like new.

Followed Mfgs instructions.

I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

My wife was complaining about poor baking results with the oven in the home we just purchased, so I hooked up my digital temperature meter and found it was almost 50 degrees of, so I tried the ovens off set program to bring it closer into range. That did the trick ,but she complained about poor baking still. I watched the oven cycle about 8 times and saw her problem. The oven was inconsistent when dropping below set temps, some times it was 20 degrees off, other times it was 80+ degrees off before the element kicked back on. I started with the sensor, it came with easy instructions including wire hi temperature wire nuts if the connectors didn't match... which they didn't. It was very easy to access the senor for replacement. Just unscrew about 10 screws, pull the back access panel off and there it is. Cut the connectors on both ends making sure to leave plenty of wire on each end. Wire nut them together and reinstall the back panel. Reset the oven off set back to zero and check the oven temp watching about 6 cycles. Comes right on now, and her first baking effort came out great...I am pretty sure that was the problem.