Quick Question!

Have you ever purchased from PartSelect.com before?

Models > B9457X0

B9457X0 Roper Wall Oven - Overview

Get Parts and Repair Help for B9457X0

If you know the wall oven repair part you need, you can browse the list of all parts on the B9457X0, or you can search by name or part description. You can also find your part by where it is located on the B9457X0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your wall oven. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$30.57

Temperature Sensor

This temperature sensor is used to measure the inside temperature of a self-cleaning oven. Its 1000-ohm resistance increases with temperature. The sensor has male leads, is 6 inche...

$17.86

Surface Burner Knob

This part is sold individually. The surface burner knob is black and chrome in color. It measures approximately 1-1/2 inches in diameter. The surface burner knob is for ranges and allows you to control the temperature of the surface burner. If your knob has broken or gone missing it will need to be replaced. This repair requires no tools to complete. You simply remove the old knob by pulling it off and press the new knob into place by lining it up with the shaft. This is an OEM genuine part.

$50.48

Broil Element - 240V

This light bulb can be used in a microwave and oven to illuminate the interior. The measurements are 5.3 x 3.8 x 1.2 inches and weigh 0.3 ounces. It is a 5 watt, 12 volt halogen li...

$5.81

Blower Wheel Clamp

This blower wheel clamp, used in a clothes dryer, is a clamp that holds the blower wheel to the motor shaft. This part helps hold the blower wheel in place to function easily and properly. If your clothes dryer has any of the following symptoms then replacing the clamp can be a solution: making loud noises, not producing enough heat or no heat at all, and/or clothes are taking too long to dry. Make sure to unplug thedryer from power source before installing this part and refer to the installation instructions provided by the manufacturer for further guidance.

$2.96

Hex Nut

This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they ar...

DISCONTINUED

NEW GOLD

Cushion-Oven Door (3 Req)

screw 10-32x5/8``

xScrew 10-32x1

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

F3 Error message

  • Customer: Charles from Brecksville, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 140 of 179 people found this instruction helpful
Two screws remove the front of the sensor (put a pan under the sensor to catch the screws), One nut removes the rear cover to access the rear of the sensor. Separating the two halves of wiring harness takes a little dexterity. BIG TIP! Tie a string to the back of the sensor wire and pull the sensor out from the front making sure the string still shows thru t... read more

Burnt out broiler element

  • Customer: Starla from Vashon, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 15 people found this instruction helpful
Turned off power to range because I was scared. Unscrewed broiler element, pulled part forward and pulled off wires that were attached to the back, attached wires to new element, pushed it back in place, screwed it back on to oven. Cooked my bruchette! read more

My stove top is 30 years old. I was down to one knob. I looked up the part by brand and age. the pictures were accurate and the size dimensions were perfect.

  • Customer: Mark from Albuquerque, NM
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 10 people found this instruction helpful
Pulled off the one remaining knob, installed the new ones. One minute and the stove works perfectly. read more