Models > AZ2727GIHB > Instructions

AZ2727GIHB Maytag Refrigerator - Instructions

All installation instructions for AZ2727GIHB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AZ2727GIHB
1-15 of 211
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.

  • Customer: David from Chester CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 62 of 75 people found this instruction helpful
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.

Ice dispenser cover flap was broken.

  • Customer: Philip from Plantation FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 52 of 52 people found this instruction helpful
First I unpluged the refrigerator, then I removed the drip shelf (slides out). Then removed the two screws hidden by the drip shelf. Then I removed the control panel by pulling out on the bottom then lifting slightly to to expose the ribbon cable. The circuit boards you see at this point will deliver an electrical shock if the refrigerator is plugged in. I disconnected the ribbon cable form the control (front) panel. Next I removed three screws that hold the chute assembly in place and worked the chute away from the door. Pay attention to the placement of the water line before you remove the chute. The bad flap fell out at this point but it is easy to fiqure out how to place the new one. When putting the chute back in place make sure the arm holding the flap is aligned in the groove of the solenoid plunger and not just setting on top. (I had to do this twice because the chute would not open the first time I put it back together). About a 30 min job because I took it apart the first time to see what was broken. I only needed the flap, the arm it mounts to an the solenoid were not broken. Easy to do and only cost about $16.00 with shipping for the part.

Refrigerator Filter needed replacing

  • Customer: Bruce from Alfred Station NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 51 of 58 people found this instruction helpful
Turn counter clockwise, following the remove arrow on the filter, until it stops. Wiggle and pull down on the filter until it comes off. Put date sticker on new filter to remember when it was replaced. Align the lines on the filter and push it up where the old one was and turn it clockwise until it stops, following the install arrow. Close the door and push both the light and lock button together to reset the replace filter light. Run the water through the door for a couple minutes to get all of the air out of the system. Very easy and quick. Most time spent flushing out the air.

No ice in ice trey

  • Customer: Wayne from Leesburg FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 43 of 50 people found this instruction helpful
The easiest thing to do was pull the ice make off. After taking the 3 screws out of the wall of the freezer, take a screwdriver (flathead) and push on the tab for the electrical plug and wiggle the cord out. Then you can take 3 screws out for the main cover and another 2 screws on the next cover. There's the part, pop it out and replace holding pins and start the process of putting back together the opposite way you took it apart.

Plastic broke where motor mounts to dispense ice so motor was just lying on the back of the enclosure.

  • Customer: Thomas from Chandler AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Wrench set, Wrench(Adjustable)
  • 25 of 28 people found this instruction helpful
Removed Enclosure, removed solenoid, removed yoke from motor, installed motor and installed solenoid. Then re installed enclosure.

The difficulty was removing yoke from motor shaft, left hand threads that were hard to identify. No place to hold shaft so it turned when trying to remove yoke.

Some minor difficulty re attaching electrical harness for motor and solenoid as I had to do it by feel. Removal was easy as the motor was just hanging and I removed the solenoid before removing the enclosure.

while closing the door, the light switch fouled, resulting in the switch breaking

  • Customer: Kevin from Beckley WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 22 of 25 people found this instruction helpful
I used a flat screwdriver and released the lock tab on the bottom of the light switch, and pried the switch out, being careful to not damage the plastic around the mounting place of the switch, unplugged wiring from old switch, plugged in the new one and pushed the new switch into place. Job finished light switch now working.

Had to replace a hose connector at the base of my refrig/frreezer

  • Customer: Leo from Salem SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 27 of 43 people found this instruction helpful
Perhaps a helpful hint:

When aI received the hose adapter/connector, I inserted the 2 hose ends only to have water drip from the connection.
I used a utility knife to remove an inch from each side, then reinserted the hoses. That made the differnce. Dry as a bone.

LG

Icemaker arm was broken

  • Customer: Jason from Austin TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 18 of 23 people found this instruction helpful
The tiny piece of plastic that holds the wire that shuts off the icemaker, broke early on with our fridge (after just a few months.) We superglued it, but last week it bit the dust for good.

Once I got this part, I removed the freezer door and trays, and pulled the icemaker out by removing 3 flathead screws and unplugging the cables. Laying in the freezer on the floor was a bit unconfortable, but not too bad.

Then I inspected the icemaker. There was no obvious way to remove the part without disassembling the front of the unit (where the motor is) to release the spindle and free the part, so I did that - 3 or 4 nuts was all that held it together. Once that was out, I removed the spindle, swapped out the part, and put it all back together and back in the freezer. Plugged it in and waited.

It took a while to start making ice. Like 5 hours. Now it's going pretty slow (much slower than before.) Haven't had time to look into it, but my suspicion is the rubber hose that feeds water into the icemaker is blocked with ice or kinked. In any case, we have ice now (but not a lot), and the unit shuts itself off properly. However, we went from having too much ice (thing never shut off) to too little (thing makes ice too slow), so I need to shoot for somewhere in the middle ;)

Ice Door Assembly

  • Customer: Robin from Knox IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 13 people found this instruction helpful
Ice door flap was broken and warm air was getting into the freezer. I removed a total of 4 screws to get to the flap. Total time was less than 15 minutes and very easy. Partselect customer service was very helpful and friendly. If you have any questions, do not hesitate to call them. They were very helpful! I have this site bookmarked!

ice maker did not make ice

  • Customer: DAVID from TINLEY PARK IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 17 of 26 people found this instruction helpful
The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.

Vegetables kept freezing regardless of temp setting.

  • Customer: John from Leominster MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 15 of 20 people found this instruction helpful
I noticed that the thin plastic flap was missing. I squeezed the housing, unsnapped and pulled. INstalling the new part was just the reverse. No more frozen vegetables.

ice dispenser won't dispense ice - auger not turning

  • Customer: Rick from KANSAS CITY MO
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 11 of 12 people found this instruction helpful
Found the problem to be a broken plastic housing supporting the auger motor — which also acts as the ice bucket shelf

I purchased a new housing/shelf and went about changing it out.

1. Lift the arm that shuts the ice-maker off.

2. Remove the ice bin. I transferred the ice to a pan
and sat it in the lower areas of the freezer.

3. Remove the screw that secures the shelf to the
left side ot the freezer. It's located on the bottom
left side of the shelf. I used a socket driver for
this.

4. Simultaneously from both the back and front of
the shelf, lift the shelf up to clear the round
supports on both sides of the freezer
compartment and then begin to pull it towards
the front of the freezer. When the back of the
shelf clears the rear round supports, let the rear
part of the shelf drop down.

5. Reach to the back left and squeeze the top and
bottom of the wiring clip, which releases it from
the back refrigerator wall. Pull it towards you as
you do this. The shelf is now totally clear to pull
out the front of the freezer.

6. Close the freezer door to protect the contents.

7. Remove the auger yoke from the motor shaft at
the front of the housing enclosure. If you have
any problems, this is the place. To begin with,
you need to know that the yoke is left-hand
threaded. Personally, I found it very difficult to
remove. I pursued another path that was not at
all helpful, so I will omit it here, but forget about
anything involving disassembly of the motor.
What you have going for you is that the motor
does not turn well from this end of the device
because of gearing. Use something long (for
leverage) screwdriver or similar item that you
can pass between the forks of the yoke and pry
it off moving it in a clockwise direction (when
viewed from the front).

8. From the rear of the housing, make note of the
configuration of the electrical connections before
proceeding. Then remove the 4 screws holding
the motor. I used a cordless drill with a phillips-
head bit in it. I left 2 screws almost loose, but not
quite, so I could remove them by hand and hold
the motor and housing at the same time.

9. ) In a similar manner remove the 4 screws
holding the solenoid and the 3 parts that it
operates. Note closely the arrangement of the
parts before removal.

10. Reinstall the motor and solenoid items in a new
shelf/housing combo and reinstall by following
these instructions in reverse order.

The motor that drives the ice auger, broke out of the plastic

  • Customer: Bill from Statesville NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 11 of 13 people found this instruction helpful
I won't repeat the removale process, straight forward. The issue is removing the U shaped driver on the motor. You have to trun it clockwise (looking at it from the front) to remove it from the drive shaft in order to install the motor on the new shelf. The problem is the motor wants to turn as well. I used skinny plyers to hold the shaft but still could not get enought presure to stop the shaft from truning. Finally decided to have my wife hold the plyers and I tapped the auger blade with a small hammer. Success. Reinstallation was simple enought.
One important key: You are not done. Once it is all reinstalled, be sure empty out the ice bin, dry all the parts as best you can, and activate the dispenser every 15 min or so for the first hour. Otherwise it will freeze up and you will think it is broken again.

Ice door plastic wing on one side broke off, keeping ice shut open.

  • Customer: Frank from Fort Pierce FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 10 of 10 people found this instruction helpful
I first removed the tray at the bottom of the Ice/water compartment, 2nd, removed the 2 star headed screws that are visible and 1 star screw near the water hose. removed front pannel. 3rd removed 4 star screws holding ice/water assembly, let this hang down and was able to reach in and removed the round broken shut door. replaced with new door, Difficult to get new door in but I was lucky and got both side wings in the proper slots. Did everything from above in reverse. New Ice doot works great. I just wish you had sent some type of instructions! Very happy with your company. Other web sites wanted me to buy a complete kit just to get the door assembly. you saved me $30. Thanks

No water in door or icemaker

  • Customer: Eric from Menan ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 11 of 17 people found this instruction helpful
From the beginning I have never had good water flow in the door and ice cubes turned out funky. I tried replacing the filter once with hardly noticeable change. The change I did see was $35 less in my pocket. So I bought a filter bypass plug and it now works like a champ. I have well water so I trust its quality and I am very satisfied. I would describe how I did the repair but if you don't no how to change out the filter you probably shouldn't be trying it.
All Instructions for the AZ2727GIHB
1-15 of 211