Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AYE2200AGW > Instructions

AYE2200AGW Admiral Dryer - Instructions

All installation instructions for AYE2200AGW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AYE2200AGW
511-525 of 666
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No power ..

  • Customer: Andy from Euless, TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
Open lid as seen on the video instructions..flat screwdriver is fine ..just make sure u pull up the lid hard since it might be a little tough to lift....follow same instructions as the video, however only part I have to tweak is...it's hard to unplug the socket to the fuse so just use flat screwdriver to losses the connectors so that u can pull it out easily...

The dryer belt broke.

  • Customer: Bill from Cooper City, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the attached video that was with the belt I ordered and it took less time to do the repair, then it did to watch the video. The video was very helpful.

Belt popped

  • Customer: Wade from Labadieville, LA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Broken belt

  • Customer: Alex Peden/ Angel from Jamestown, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

Dryer drum not turning.

  • Customer: charles from stanhope, NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed top and front panels, lifted front of drum, slid new belt on drum then thru tension and motor pulleys. reassembled.

Would not start

  • Customer: James from Cary, NC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Easy on Kenmore Performa Dryer, order the High Limit Kit, it got here in 3 days. Unplug from wall, use flathead screwdriver to pop up the top; then look for the High Limit just behind the drum and the smaller fuse below that one on the right. Best to have smaller hexagon ratchet, and be careful not to drop them behind the drum. When you undo the high limit, use needle nose pliers to pull of the contacts from it. Then just attach as you disconnected, be sure you know which was which. Then remove the old smaller one, it can be tricky, and install new one. Then just close up the top, plug it in and it should start right up. Have replaced this every few years, easy and affordable.

drum would not turn

  • Customer: tim from meriden, CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
quite simply I followed the path that was worn from years of use. it was very apparent the belt had broke. along with the belt there was a generic diagram for proper install. this was very helpful

left roller support shaft has flat on one side

  • Customer: Roger from Merrillan, WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
1.used small flat head screw driver to pop top of dryer. 2.used phillips screw driver to remove front of dryer. 3.disengage dryer belt. 4.take hold of brum and turn and pull out. 5.{left side}take snap ring,washer,roller off then remove support shaft. 6.install new parts, support shaft,roller washer, snap ring. 7,right side has a plastic washer that goes on before roller rest will be as step 5 8.put dryer back together.

Dryer belt broke

  • Customer: Jim from North Smithfield, RI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
took the dryer apart noticed it needed a belt and rear drum supports. Ordered the parts(they were very helpful on getting the right part . they came in very fast (less than 24 hours). replace the broken parts. The dryer is working great.

Dryer drum belt broke.

  • Customer: Martha from Chancellor, AL
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Opened dryer top, disconnected door wireing, took off front panel, laid dryer on back, cleaned out lint and inside, put new belt on, and put parts back together. Dryer works fine now.

Drive belt broke

  • Customer: Robert from Port Arthur, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

Belt broken & toe panel was loose

  • Customer: Jim Ten from Sheboygan, WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

broken control knob

  • Customer: Robert from Lagrange, IN
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The repair was pretty easy just pull off the old and slip on the new one just a couple of minutes and it worked great. The part site was easy to order off of

My dryer won't turn on.

  • Customer: Charles from Yorktown, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The dryer would not turn on so I checked the power. I then googled the problem and found that the high limit fuse was bad. I ordered the part and simply replaced the fuses after watching the video on the website. Simple and easy. Thanks!

dryer belt broke

  • Customer: LAWRENCE from BANDERA, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.
All Instructions for the AYE2200AGW
511-525 of 666