Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW701F1D

AW701F1D Kelvinator Washer - Overview

Get Parts and Repair Help for AW701F1D

If you know the washer repair part you need, you can browse the list of all parts on the AW701F1D, or you can search by name or part description. You can also find your part by where it is located on the AW701F1D by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW701F1D parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.91

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

Order within the next 8 hrs and your part ships today!
$6.55

SCREW

Sold individually.

Order within the next 8 hrs and your part ships today!
$22.37

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you ...

Order within the next 8 hrs and your part ships today!
$5.13

Single Tub Cover Clip

Order within the next 8 hrs and your part ships today!
$8.47

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for t...

Order within the next 8 hrs and your part ships today!
$8.76

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. This part goes between the timer knob and the dial in a washer to function effectively and provide protection. The length of this part is 6.35 inches with a width of 5.25. The spacer has a height of 8.125 inches and the weight of 0.3 pounds. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to unplug your appliance from the power source.

Order within the next 8 hrs and your part ships today!
$16.34

V-Style Belt

This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you no...

Order within the next 8 hrs and your part ships today!
$7.00

Fill Hose Washer

1 per package.

Order within the next 8 hrs and your part ships today!
$4.90

SCREW

Order within the next 8 hrs and your part ships today!
$7.51

SPRING

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer Continued To Fill To Point Of Overflow

  • Customer: alvaro from east hampton, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 64 of 72 people found this instruction helpful
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connec... read more

Leaking washing machine.

  • Customer: Ron from Williamsburg, MI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 23 of 35 people found this instruction helpful
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops.... read more

belt worn causing machine to make all kinds of noise

  • Customer: Kenneth from Baltimore, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 18 of 25 people found this instruction helpful
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!! read more