Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW500C2T

AW500C2T Kelvinator Washer - Overview

Get Parts and Repair Help for AW500C2T

If you know the washer repair part you need, you can browse the list of all parts on the AW500C2T, or you can search by name or part description. You can also find your part by where it is located on the AW500C2T by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW500C2T parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$18.87

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

$6.36

SCREW

Sold individually.

$22.37

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you ...

$8.34

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

$15.91

V-Style Belt

This v-style belt or drive belt is designed for use in your washing machine. This part connects the drive motor to the drive system in the washer, which spins the basket. If you no...

$8.76

SPACER

This spacer is used in washers or a washer and dryer combo unit. Spacers are used to create space between cotter pins, lock nuts, hitch pins or to fill the space between machinery parts in a washer. This part goes between the timer knob and the dial in a washer to function effectively and provide protection. The length of this part is 6.35 inches with a width of 5.25. The spacer has a height of 8.125 inches and the weight of 0.3 pounds. Refer to the manual provided by the manufacturer for further installation instructions and guidance. Remember to unplug your appliance from the power source.

$5.19

CLAMP

$4.69

SCREW

$365.67

Transmission Assembly

This part aids in the spinning or agitating cycles.

$40.24

HOSE-INLET 60"

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer Continued To Fill To Point Of Overflow

  • Customer: alvaro from east hampton, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 63 of 71 people found this instruction helpful
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connec... read more

Leaking washing machine.

  • Customer: Ron from Williamsburg, MI
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 23 of 35 people found this instruction helpful
Removing the piece above the tub gasket was very difficult. A lot of hammer and chisel work.
15 year old machine. A lot of calcium build up around the shaft. I used a screw driver as a chisel and a hammer. Carefully removed the metal around the shaft to get to the tub seal.
Once I got to the tub seal it was easy. Remove the old rubber stops.... read more

belt worn causing machine to make all kinds of noise

  • Customer: Kenneth from Baltimore, MD
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 18 of 25 people found this instruction helpful
pull up on top ,take two screws loose on front panel(pull off) vaccum old debri out,pull tension pulley back pull old belt off,holding tension pulley put new belt on .put front panel back on and snap top back down to secure.
working perfectly nice and quite !!! read more