Models > AW26K3H Maytag

AW26K3H Admiral Washer - Overview

Get Parts and Repair Help for AW26K3H

If you know the washer repair part you need, you can browse the list of all parts on the AW26K3H, or you can search by name or part description. You can also find your part by where it is located on the AW26K3H by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW26K3H parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$14.68

Drive Belt

This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get we...

$4.75

Snubber Ring

$44.48

Drain Pump with Pulley

This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$36.18

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are not available separately - only available in this kit. A worn bearing causes slow or no spin.

$2.70

Screw

This screw is sold individually.

$2.70

Hose Clamp

$2.70

SCREW

This screw is sold individually.

$7.86

Leveling Leg and Pad

This part includes locknut.

$2.70

Screw

This screw is sold individually.

$44.61

Washer Brake Rotor

This part aids in the spinning or agitating cycles.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 111 of 122 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more

PUMP MAKING HORRIBLE NOISE AND BRAKE STUCK

  • Customer: MICHAEL from PLYMOUTH MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 58 of 66 people found this instruction helpful
The pump was very easy to replace (3) screws, easy to reach with front panel off. (less than 5 minut job. The brake assembly and thrust bearing was a little harder to do, but not bad at all. I found it best to flip the unit upside down to do the brake assembly. Replaced #10-24 x 1/2" screws with 2" long ones. Remember to do this (1) at a time, then back all ... read more

washer would agitate, pump, but not spin

  • Customer: steve from lebanon OH
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 28 of 33 people found this instruction helpful
First I unplugged it, then removed the agitator and tub assemblies, then I tipped it back and removed the belt and pully and thrust bearings. After reading on here I learned the brake would stick and after installing the thrust bearing kit I found out I couldnt fit in the shims. That led me to believe the brake was siezed inplace so i couldn't fit in the par... read more