Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW25K3A Maytag

AW25K3A Admiral Washer - Overview

Get Parts and Repair Help for AW25K3A

If you know the washer repair part you need, you can browse the list of all parts on the AW25K3A, or you can search by name or part description. You can also find your part by where it is located on the AW25K3A by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW25K3A parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$5.26

Snubber Ring

The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the ...

$52.97

Transmission Pulley and Bearing Kit

This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.

$72.17

Drain Pump with Pulley

This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing mac...

$3.02

Screw

This screw is sold individually.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$6.68

Screw

This screw is sold individually.

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...

$9.14

Leveling Leg and Pad

This leveling leg, which includes a lock nut and a pad, is used to keep washing machines still and balanced. If your washer shakes and moves excessively, then this could be an easy and quick solution to your washers problem. To install, the damaged pulley must be removed to install new pulley. The suggested tools are pliers, a socket set, and/or screwdrivers. For safety precautions, make sure to unplug washer from power source or shut off the house circuit breaker. Remember to wear gloves prior to starting this installation project. Refer to the instructional diagram provided by the manufacturer for further guidance. Customers suggested the detailed diagram as helpful.

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$11.46

Spray Paint - 12 oz. - White

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a protective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 536 of 541 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 134 of 146 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more

Pump Making Horrible Noise And Brake Stuck

  • Customer: MICHAEL from PLYMOUTH, MN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 102 of 120 people found this instruction helpful
The pump was very easy to replace (3) screws, easy to reach with front panel off. (Less than 5 minut job. The brake assembly and thrust bearing was a little harder to do, but not bad at all. I found it best to flip the unit upside down to do the brake assembly. Replaced #10-24 x 1/2" screws with 2" long ones. Remember to do this (1) at a time, then back... read more