Models > AW20N2V > Instructions

AW20N2V Admiral Washer - Instructions

All installation instructions for AW20N2V parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AW20N2V
76-90 of 360
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Front legs came off while moving causing cycle pulley to rub on the floor.

  • Customer: Jerry from Dayton TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 15 people found this instruction helpful
Removed damaged pulley installed new pullley and clutch. The directions made it easy. Aligned pulley as detailed and installed new front feet and tested washer. Took me about 30 minutes to repair. Washer has been working since. Thanks guys for a nice no nonsense package.

lid switch acuator broke and some cycles would not work

  • Customer: Brian from Woodbury MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
unscrew the screw holding the broken part in the lid to remove the old part and tighten the screw to a firm position to hold the new piece in place. Now working fine.

Washer Spin Cycle Stopped

  • Customer: Diana from La Mirada CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
Removed the screw from the side of the lid of the washer. Took off the old Lid Switch Actuator and screwed in the new one. Took a little elbow grease because the old screw was tight but no longer than 15 minutes tops.

motor pully broke

  • Customer: Anthony from Bryceville FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Socket set
  • 3 of 4 people found this instruction helpful
First our local store said you had to buy the whole motor. I didn't. I bought the pully from you guys and took pliers and pulled the broke pully off and put a socket on there and hit it with a hammer and then she washes.

Top cabinet was rusted on one corner due to liquids dripping from a shelf

  • Customer: John from Spring Valley CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
1. Disconnected the electrical cord from the socket & the hose lines from the faucets.
2. Pulled out the washing machine from against the wall to make room for working.
3. Opened the back of the control cabinet by removing the 5 screws.
4. Disconnected the wiring ( making sure to identify all connections and color of wiring ) from the control cabinet and pulled through the opening on the cabinet top.
5. Popped the lid open from the front of the washer using a screwdriver by prying it open and removed the hinge lid from the cabinet top.
6. Removed the control cabinet from the cabinet top, disconnected the safety latch from the cabinet top.
7. Removed the water inlet guide & a vacuum hose from the cabinet top.
8. Removed the hinge brackets from the back of the washer which holds the cabinet top in place.
9. Removed the hinged lid from the cabinet top..
10. Installed new hinges on to hinge lid .

Installed new cabinet top in reverse order as above.

I had water leaking from the top of the tub.

  • Customer: Lester from Elk Grove CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

loud squeal when stopping and leaking

  • Customer: Michael from Carmel NY
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Socket set
  • 2 of 2 people found this instruction helpful
Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

No belt and no motor gear

  • Customer: Matt from Hoboken NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 2 of 2 people found this instruction helpful
Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.

My washing machine would be extremley loud when washing clothes then one day it stopped working.

  • Customer: damian from carpentersville IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

Noise from pump

  • Customer: Donald from Brielle NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 3 of 5 people found this instruction helpful
On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

Wind blew lid off washing machine while being moved

  • Customer: Lisa from West Branch MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

Plastic Lid Hinge was broken

  • Customer: Thomas from Coral Springs FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 2 people found this instruction helpful
Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from underneath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.

Lid hinge broken

  • Customer: Elwyn from Kansas City MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

It squeaks when stop spinning

  • Customer: Hing from Toms River NJ
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 3 of 5 people found this instruction helpful
I think normally the problem is caused by the Brake Rotor Lining Assy (item #50 on the diagram). It has a brake lining facing down that makes contact with item # 51. It turned out that I had grease & grime on these parts, thus the brake is not taking grip & causing squeaky noise. All I had to do was to clean the parts & put them back. I bought the part (#50) - P/N 2347192, but it was a whirlpool part that didn't fit my Magic Chef. Some parts fit both brands, but this 1 didn't. Here is the procedure:

1. Unplug washer.
2. Move unit away from wall.
3. Tilt it back far enough to work underneath. Support the front with lumber.
4. Pull out cap (#58)
5. Remove ring clip (#57)
6. slide out everything from #53 down. Keep them in same order for re-installation.
7. There are 6 ea screws (#53) that hold item #52 to item #45. It is spring loaded by item #47. Item #53 has a 5/16" hex head. Use 3 ea. #10-24 hex head screw, at least 1.25" long to assist in compress/decompress the spring tension. You can buy them from a hardware store.
8. Take out every other screw (#53) & replace them with these 3 longer screws for remove/re-installation of item #52.
9. Take out the remaining 3 ea #52 screws.
10. Go around & back off each of the 3 longer screws to decompress the spring.
11. Remove item #52, & everything from #48 down will come out.
12. Clean or replace what you need.
13. Do the reverse to put everything back.
14. There is an item within #59 that looks like a miniature bearing. I would put some grease on that & on item #55.

will not agitate

  • Customer: albert from south milwaukee WI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 3 people found this instruction helpful
remove top and front panel to access wash drum. unhooked suspension/balance springs(6).also removed drive belt. removed half of brake bolts installed 3 1-inch bolts removed 3 remaining short bolts,then 3longer bolts to remove tension of brake spring. removed/dissassembled brake and snubber ring,then reassembled in reverse order. wish i would have replaced suspension springs at same time! ordered new springs today
All Instructions for the AW20N2V
76-90 of 360