Models > AW20N2V > Instructions

AW20N2V Admiral Washer - Instructions

All installation instructions for AW20N2V parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AW20N2V
61-75 of 350
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaky hose resulted in damaged Thrust Bearing

  • Customer: Steven from Gilbert AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 5 of 8 people found this instruction helpful
After replacing the tub to pump hose, I adjusted the feet on the washer. Apparently, the main pulley sits so low on these washers that it ground into the floor and stripped out the thrust bearing. I ordered the new thrust bearing clip and put it in the evening I received it. The instructions it came with were very helpful and it was simple to reassemble. Up until the last piece - the retaining clip. The majority of the repair time was spent replacing that clip. If there is a tool that makes the job easier, I didn't have it. I finally got it on with two flathead screwdrivers prying the shaft out while I wedged one corner of the clip in the groove.

White fluffy residue appeared under washer. Unbalanced banging during spin cycle

  • Customer: John from Blue Bell PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 4 of 5 people found this instruction helpful
Parts needed: Snubber Ring and 6 Springs (don't put the old springs back)
Unlug the AC cord, open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back It was not necessary to remove the back cover. Remove the little hose going to the basket from the control module. Remove the 6 springs and lift the complete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING: DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK. Seriously! Install the new ring, center and tighten the screws. Put the tub back in. I found it handy to support the tub with a 2x3 to get the springs back in. Connect hoses back up. It really isn’t that bad, a couple of scraped knuckles.

washer lid was no longer connected

  • Customer: linda from granada hills CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

Water wouldn't stop

  • Customer: Steven from Westfield MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 6 people found this instruction helpful
Unplugged washer then took back off control panel. Removed clamp and tube from pressure switch. Pushed in tabs with a screwdriver and lifted top. Removed clamp and broken tube. Put new tube in place and tighten clamp with nutdriver. Closed top and put other end of tube on pressure switch with clamp. Put back on control panel and plugged in. Clamps are to big for application but do work. So far so good!

lid hinge broken

  • Customer: VALERIE from PARKER CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I'm a 69 year old female. My husband isn't very handy so I decided to order the parts and do it myself. I didn't know how to take the machine apart so I just moved the washer part so I could unscrew the screw. I dropped the screwdriver between the adj. and side of the washer. I guess you won't be telling this story. I did get the parts on and the lid is working and so is the machine. Valerie Guyot

Front legs came off while moving causing cycle pulley to rub on the floor.

  • Customer: Jerry from Dayton TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 15 people found this instruction helpful
Removed damaged pulley installed new pullley and clutch. The directions made it easy. Aligned pulley as detailed and installed new front feet and tested washer. Took me about 30 minutes to repair. Washer has been working since. Thanks guys for a nice no nonsense package.

washer was squeeling to a stop

  • Customer: paul from newbern TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 4 of 6 people found this instruction helpful
first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

My Washer's lid hinges broke while it was being moved.

  • Customer: Gary from Mesa AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

Pully was broken, belt worn in one spot

  • Customer: Clarence from Crosby TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 9 people found this instruction helpful
Remove screws holding backplate, reomved backplate. removed belt and pully, replaced pully, replaced new belt, returned backplate and screws. worked great

drive pulley split in half after installing new belt

  • Customer: David from Haverhill MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 3 people found this instruction helpful
I used two pry bars to evenly and gently remove old pulley then I gently hammered new one in place and reinstalled belt.

Washer lid came off hinges

  • Customer: Geoffrey from Knoxville TN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.

during wash cycle, water poured out of bottom of washer

  • Customer: Susan from Cloquet MN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 5 of 10 people found this instruction helpful
first we looked at schematics on your web site to see what we thought was wrong and if we felt we could do ourselves. It appeared to be seals and gaskets, so we went for it and carefully took the washer apart. We ordered the parts, cleaned the parts we had such as the tub, and were all ready to put back together when the parts arrived. Again, using your pictures, we reasselbled and when we tested, it worked better than it had been in a long time. And we saved a large repair bill!

broken pump, burned belt

  • Customer: Jeffery from Omega GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Socket set, Wrench set
  • 3 of 4 people found this instruction helpful
I removed four screws to remove a plate to get access to the pump. Then I removed 3 screws to remove the pump. I then put the new pump in place and put the 3 screws back in the pump. Then I put the plate back on and put the 4 screws back in. Then I put the belt on and put the washing machine back in place and connected the water lines and drain line and plugged the washing machine back in and then tested the washing machine to make sure it worked. Job completed.

Top cabinet was rusted on one corner due to liquids dripping from a shelf

  • Customer: John from Spring Valley CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set
  • 3 of 4 people found this instruction helpful
1. Disconnected the electrical cord from the socket & the hose lines from the faucets.
2. Pulled out the washing machine from against the wall to make room for working.
3. Opened the back of the control cabinet by removing the 5 screws.
4. Disconnected the wiring ( making sure to identify all connections and color of wiring ) from the control cabinet and pulled through the opening on the cabinet top.
5. Popped the lid open from the front of the washer using a screwdriver by prying it open and removed the hinge lid from the cabinet top.
6. Removed the control cabinet from the cabinet top, disconnected the safety latch from the cabinet top.
7. Removed the water inlet guide & a vacuum hose from the cabinet top.
8. Removed the hinge brackets from the back of the washer which holds the cabinet top in place.
9. Removed the hinged lid from the cabinet top..
10. Installed new hinges on to hinge lid .

Installed new cabinet top in reverse order as above.

I had water leaking from the top of the tub.

  • Customer: Lester from Elk Grove CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
All Instructions for the AW20N2V
61-75 of 350