Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW20L4W Maytag

AW20L4W Admiral Washer - Overview

Get Parts and Repair Help for AW20L4W

If you know the washer repair part you need, you can browse the list of all parts on the AW20L4W, or you can search by name or part description. You can also find your part by where it is located on the AW20L4W by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW20L4W parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$56.03

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - t...

Order within the next 6 hrs and your part ships today!
$34.73

Lower Bearing Assembly

Order within the next 6 hrs and your part ships today!
$38.58

Lid Switch Kit

This kit includes the bracket, actuator, switch, screws and wire harness.

Order within the next 6 hrs and your part ships today!
$13.74

Flume Hose Kit

Order within the next 6 hrs and your part ships today!

KNOB- SELE

$7.40

Cabinet Top Hinge

Order within the next 6 hrs and your part ships today!
$6.33

WASHER

Order within the next 6 hrs and your part ships today!
$24.31

Knob and Indicator Skirt

Order within the next 6 hrs and your part ships today!
$11.56

Stabilizer Bracket

This part works along with the stabilizer bar, at the base of your washer, to keep your appliance more stable during the spin cycle.

Order within the next 6 hrs and your part ships today!
$4.94

NYLITE WAS

Order within the next 6 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 520 of 525 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 478 of 475 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 133 of 145 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more