Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW20K3 Maytag

AW20K3 Admiral Washer - Overview

Get Parts and Repair Help for AW20K3

If you know the washer repair part you need, you can browse the list of all parts on the AW20K3, or you can search by name or part description. You can also find your part by where it is located on the AW20K3 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW20K3 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Sections of the AW20K3

[Viewing 1 of 1]
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.52

Lid Hinge

The lid hinge on your washer is connected to the lid and allows it to open and close. If you find you cannot open or close the lid to your washing machine properly, you may need to...

$9.64

Lid Hinge Pin

This lid hinge pin allows a washing machine lid to pivot open and closed properly. The hinge pin may need to be replaced if the lid will not open or will not close. The part is white and made of plastic. This lid hinge pin is just over an inch long, is sold individually, and does not include the mounting screw (consider ordering mounting screw if it rusted or stripped). It is recommended to check the opposite lid hinge pin before ordering because hinges may wear at the same rate. Be sure to not tighten the mounting screw to pin too tightly to avoid breaking the new part.

$5.05

Screw

This screw is less than an inch long. It is a metallic screw that is used for many clothes washers.

$3.02

Screw

This screw is sold individually.

$23.46

Lid Switch Actuator - Black

This is part of the lid switch actuator mechanism and activates the lid switch, when the lid is closed, to start the wash cycle and when the lid is open, it stops the cycle.

$42.83

Lid Switch Kit

The lid switch kit is an assembly for replacing your washer lid switch. The function of this part is to detect if your washer lid is open or closed. If it detects that it is open it will prevent the washer from rotating and agitating until it is closed. This kit includes the bracket, actuator, switch, screws, and wire harness. To complete this installation, you will need a number two Phillips screwdriver, and a 5/16 nut driver. Before beginning this repair, make sure the power supply to your washer is disconnected. In order to install this part, you will need access to the rear of the unit.

$12.12

Cabinet Top Hinge

$207.04

Top-Load Lid - White

$35.00

Single Front Panel Clip

This front panel clip is just about an inch long. It is green in color and is made of metal. This clip is intended for use with the front panels of washers and dryers.

$6.49

Plate Nut

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 487 of 485 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Intermittent problem with lid switch, no high speed spin/pump out

  • Customer: Linda from La Porte, IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 37 of 51 people found this instruction helpful
Disconnect power, unsnap and raise machine top cover w/lid, remove old switch - two screws under lid, taking care to not drop loose actuator lever into machine. Remove control panel back and disconnect switch wire connector. Intall new switch, taking care to not drop loose actuator lever into machine, connect switch wires inside control panel. Replace pan... read more

Hinge pin on one side and Lid hinge on the other

  • Customer: Jon from Ridgecrest, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 31 of 35 people found this instruction helpful
First I popped the lid up to about 70 degrees. Then removed the two hinges. Then removed and replaced the two hinge pins. The key is to then just start the two screws for the hinges, slip the pins in and then tighten the hinge screws. Total time was 5 minutes. read more