Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AW100KD2

AW100KD2 Kelvinator Washer - Overview

Get Parts and Repair Help for AW100KD2

If you know the washer repair part you need, you can browse the list of all parts on the AW100KD2, or you can search by name or part description. You can also find your part by where it is located on the AW100KD2 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AW100KD2 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.55

Drive V-Belt

This rubber V-style drive belt slips on the motor pulley to bring the basket to the required speed. If you notice a burning rubber smell or grinding noises coming from your washer,...

Order within the next 7 hrs and your part ships today!
$5.36

Screw-In Plastic Leveling Leg

Sold individually.

Order within the next 7 hrs and your part ships today!
$18.87

Water Inlet Valve

The water inlet valve has two ports for water to enter and controls the flow of water into a washing machine. Hot, cold, and warm water can easily enter the washer this way. If the...

Order within the next 7 hrs and your part ships today!
$9.28

Tension Idler Pulley

The idler pulley on your washing machine allows the drive belt to operate smoothly. If your washer is not spinning or agitating, makes too much noise, or you notice a burning smell when it is operating, you might need to replace the tension idler pulley. The tension idler pulley works in conjunction with the drive belt, so you might need to replace the belt as well as the pulley. Once the old pulley has been removed from the washer, you will need to transfer the spring and bushing from the old pulley to the new one before re-attaching it to the washer.

Order within the next 7 hrs and your part ships today!
$22.37

Snubber Ring

The snubber ring on your washing machine mounts at the base, under the support. If you notice that your washing machine is vibrating, shaking, or moving during the wash cycle, you ...

Order within the next 7 hrs and your part ships today!
$30.10

Splash Cover Seal

Order within the next 7 hrs and your part ships today!
$28.79

Tension Spring

This tension spring works in conjunction with the idler pulley. The spring is part of your top load washing machine assembly. The most likely reasons for needing to replace the ten...

Order within the next 7 hrs and your part ships today!
$8.91

SPRING

Order within the next 7 hrs and your part ships today!
$28.52

Horizontal Spring

Order within the next 7 hrs and your part ships today!
$8.34

Upper Spin Bearing Washer

The upper spin bearing for a washer can solve many issues such as loud and odd noises, or leaking water. Replacing the spin bearing could solve these issues. The tools needed for this replacement are screwdrivers, a socket set, and a putty knife. To repair, first lift the top of the washer and remove the screws at the bottom of the front panel to pull away. Next, pull off the dispenser cover, cup, and agitator. Detach switch tube from the tub cover and remove tub cover, then use the 1/2 inch socket to remove the trunnion bolts and pull out inner tub. For the rest of the installation instructions, refer to the diagram provided by the manufacturer. Remember to unplug the appliance from the power source as a safety precaution.

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

replace broken drive belt

  • Customer: rodney from fairfield bay, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 220 of 245 people found this instruction helpful
carefully pry up on front washer top to release plastic keeper pins,remove 2 phillips screws from beneath lower front washer panel,slightly lift upward on panel to release.remove old broken belt,push new belt beneath large tub pulley,put belt on small motor pulley,push back belt tension /idler arm,start belt on large tub pulley,turn tub pulley by hand to run... read more

Washer Continued To Fill To Point Of Overflow

  • Customer: alvaro from east hampton, NY
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 63 of 71 people found this instruction helpful
First I removed the top panel held by four screws at rear of panel, pulling the panel foward and up. Then disconnected the power and water connections. Then I removed the two screws holding the flow valve to the washer rear panel,pulled the valve foward ,removed the two electric connectors, pinched the water clamp with pliers and removed the water connec... read more

Lid Lock Assembly broke

  • Customer: Jenessa from Tacoma, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 57 of 69 people found this instruction helpful
The Lid Lock Assembly came super fast! The install would have been flawless, but the "pre-drilled" holes on the new Lid Lock Assembly were way to small. We found that out after we had reconnected the wires and gotten it into place. Aside from that small set back, the install went great! This repair is definitey not one that you would need to pay a repair... read more