Models > ATW4475TQ0 > Instructions

ATW4475TQ0 Admiral Washer - Instructions

All installation instructions for ATW4475TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATW4475TQ0
496-510 of 561
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Extremely wild rocking in spin cycle

  • Customer: Bryan from Midland NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Followed the instructions given in the video. Exactly as per video instructions.WATCH THE INSTRUCTIONAL VIDEOS!!

Tub was spinning only part time. Had to have help getting started

  • Customer: Kingsley from Ewing IL
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Installed new clutch assembly and while I was at it replaced the Motor Coupling. Actually, I had a good time doing the repair. I am almost 80 years old, so had to have help laying the washer on backside. Got a small stool from which to work (back problems). The only thing I found the least bit difficult was reinstalling the retaining clip for the clutch assembly. The rest was a piece of cake. Were I to do the same repair now, it would take less than 30 minutes. Washer works like new now. Very proud of what I was able to accomplish. Of course, need to watch the repair video so you will know where to start.

There was a hole in the outer tub

  • Customer: Kevin from Boise ID
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I went to you tube and watched a video on how to take my machine apart.Everthing went great.I did need to buy a spanner for $23.00 @ an appliance store.

Tub will not spin

  • Customer: Rick from Terre Haute IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After finding out the tub would not spin, I removed the washer to find broken pieces on the floor. I did a google search on my model number and found that the problem was the direct drive motor coupling (it matched the pieces on the floor). So, I watched the "how to" video and I followed the steps verbatim. I found the coupler missing and the plastic pieces on the drive broken. My order came in quickly (within 48 hours) and my washer was running in 20 minutes after receiving the package. It has been great ever since.

Washer would stop during any cycle until lid is opened and closed.

  • Customer: Edward from Denver CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplugged the washer. Removed the 2 screws on back of control panel. Pulled the control panel forward. Flipped the control panel back. Disconnected the cable from the lid switch. Removed the ground screw with a nut driver. Opened the washer lid. Removed the lid switch. Snapped the new lid switch into place. Closed the lid. Installed the ground screw. Installed the lid switch cable. Put the control panel back in place and pushed back. Installed the 2 rear screws into the control panel. Plugged the washer in.

Washer would stop between cycles

  • Customer: James from Wichita Falls TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I unplugged washer, then, removed the control panel with two screws on back, slid unit back and up. Unscrewed ground screw and unplugged harness, lifted lid and removed switch. In order to re-install lid switch, lid has to be in the up position, otherwise it will not fit properly. Reattach harness and ground screw, then control panel. Plug and go. My wife says that the washer works better than ever. Very easy! Saves money!

Washer vibrating when in spin cycle.

  • Customer: Calvin from Cheney WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Replaced suspension, leveling and tub springs.

Motor Coupling Broken

  • Customer: Jeff from Nicholasvile KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I followed the 'how to' video, stopping the video when needed to complete a portion of the repair. I was doing the repair in a laundry closet, which took me a little longer, but with the right parts ordered and the instruction video this project was easy and does not take very long.

Clothes soaking wet after wash cycle completed

  • Customer: Justin from O'Fallon IL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I followed the helpful video from PartSelect. Removal and Replacement of the Clutch Assembly was fairly easy. Just make sure you have enough towels to dry up any water that may come out after tipping the washing machine over. After Replacement the washing machine works like new. Thanks PartSelect.

Machine had been walking and vibrating for a couple of months during the spin cycles.

  • Customer: Roland from Navarre FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Looked on line and found the cheapest repair for my symptoms seemed to be the tub wear pads. Disconnected the washer, tilted it to where I could inspect the pads and discovered one was missing. So ordered a set, (Only complaint was the shipping was as much as the part). Parts arrived in 2 Days (!). Tilted the washing machine again...reached up with a small flathead screw driver and pryed the old pads off...snapped the new ones on (takes a little pressure, so eat your wheeties)...and job done. Stood everything back up and re-connected hoses, drain and plug...Works like brand new...Unfortunately for the wife who thought she was going to get a new one....LOL

The washing machine started making a clicking type noise and would not drain after the rinse cycle completed.

  • Customer: Larry from Buffalo TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After entering the Parts Select website and searching for the model number information, I found a video which described the problem. The video explained the step by step procedure to access the possible problem. The problem was exactly as the video described, I ordered the repair part, made the repair, and placed the washer back in service. Oh, by the way, the part was delivered to my house the next day.

Would not spin out all the water from clothes

  • Customer: Michael from Tallahassee FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Similar to the youtube repair video, followed it mostly. This model has a different plug in set up on top where the wiring is. Just unplugged a different plug in a different location. The other difference is that I did a lot of dusting and vacuuming of inside parts and around motor. Also used some spray on rust converter on some rust spots then coated those areas with spray paint. Also where wire harness hooks to the frame I taped up a longer section of the wire to keep the wires together so they could move around and not be damaged. The actual repair took about a half hour, but took more time taking the washer outside on porch then back into the house. Out side repair is better because a significant amount of water came out of the washer and drain hose when we tilted it on the back to remove motor and transmission. Just follow the youtube video instructions and most people should have little or no problems doing the job.

Nonworking agitator

  • Customer: David Wade from Great Barrington MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I basically followed the YouTube tutorial on the PartSelect site. Essentially all that was wrong with my machine was that the nylon "dogs" had deteriorated, but I decided to replace the entire core--total cost including shipping, about $28. I had more trouble getting the top part of the agitator off than was depicted in the tutorial, but it's an old machine and there was a lot of old detergent residue, which I cleaned off. This actually took the majority of the repair time. It now works just fine.

The tub would not spin during the spin cycle. I diagnosed that the door switch was functioning. And through some reading on the internet, found out it was the motor coupling. I replaced the clutch assembly strictly as preventative maintenance.

  • Customer: Jorma from Saint Cloud MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I am not even going to attempt to explain. The videos that were brand specific are all anyone needs to complete any repair. They are very well made. And easy to follow. Thank you for saving me a repair call!

Chlothes were coming out wet at the end of the cycle.

  • Customer: James from Bel Air MD
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Parts select gives you the top solutions for the problem you are having. This suggested a clutch, and upon looking at mine I could see it was displaced. I watched the instructional video, and it was spot on. It told me how to from beginning to end and it worked out perfectly. I spent about an hour of my time, spent $38, and my machine is fixed. Thank you Parts select for the free video, I couldn't have done it without it.
All Instructions for the ATW4475TQ0
496-510 of 561