Models > ATW4471TQ0 Maytag

ATW4471TQ0 Admiral Washer - Overview

Get Parts and Repair Help for ATW4471TQ0

If you know the washer repair part you need, you can browse the list of all parts on the ATW4471TQ0, or you can search by name or part description. You can also find your part by where it is located on the ATW4471TQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ATW4471TQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added stren...

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$21.75

Lid Switch

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.

$2.18

Inner Cap Seal

Also known as an O-Ring.

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$2.52

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. Th...

$3.76

Tub Spring

$3.76

Agitator Cap Barrier with Seal

$8.76

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No movement from Basket & agitator

  • Customer: Jeff from Wayne NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 468 of 496 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

spin cycle did not engage

  • Customer: Andrew from SLC UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 175 of 189 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

Broken Coupling

  • Customer: Hugo from Frisco TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 143 of 151 people found this instruction helpful
Very easy -
1. Removed hoses from the pump
2. Removed Wiring harness from the motor
3. Unscrewed saftey screws from both clamps which hold the motor against the motor bracket.
4. Using a screw driver I easily removed/pryed the clamps from the motor.
5. I then removed the broken plastic coupler from the motor shaft and installed the... read more