ATW4300TQ0 Admiral Washer - Instructions

well my Dearest Kenmore washer was vibrating badly so i looked the part in yoursite of parts select it diagnosed it i ordered the 2 different supension pads relaced then and now my Dearest kemore washer works like new again Thankyou Parts select for all your help and the price was perfect...

Followed an online video. Very informative.

Video's on parts select are a big help. Just followed the instructions. Only slight problem was the coupling's do not slide easily onto the shafts. I had to use a little lubricant and put a wood block across the opening and tap with a hammer. Maybe a little more than a tap. Also when I was ready to test the repair I found the washer would not stop filling. After much checking I found out on another repair site that the shutoff requires a certain water pressure to work properly. I hadn't opened the faucet fully. Once I did everything worked properly.

Removed the washer enclosure, removed the hoses, cleaned everything, installed the new hoses, reinstalled the enclosure, test run the washer and it's working now.

The most difficult part was aligning the two sides of the coupling. Disassembling the motor from the transmission was a snap. The replacement coupling was of higher quality than the original. It had metal bushings in the center holes, where they interface each driveshaft. The original did not. It was plastic.

The repair went very well as per the video, however the metal reinforced coupling only went onto the shaft half way. To ensure the coupling was flush with the top of the shaft I has to use a hammer and tamp the coupling onto the shafts. If you left it halfway on the shafts there was no room for the rubber spacer between the couplings. Other wise it operates very well.

I was in need of a second washer to wash heavily soiled clothes my daughter in law younger sister was throwing one away so I asked what was wrong with it and was told it wouldn't spin so I thought it would be an easy fix I brought the washer home did a quick check and with the internet guide I was able to determine the problem I ordered the part and thank god once the part arrived I was able to do the repair within minutes now I have a second washer to due heavily soiled clothes and no more trips to the laundry mat thanks a million to your step by step guide couldn't have done it with out you

You guys are "Awesome" I wish I had known about your site and watched the video's first!!! When my washer started acting up, I tore it down to parade rest trying to figure out why it wasn't spinning! Then I discovered your web site searching for help. Anyhow, it identified my problem, I watched the video on the most likely cause (the Direct Drive Motor Coupling), checked it out, and discovered one of the couplings was cracked and rounded out..... Thanks to you, the washer's fixed and I can't Thank you enough! Sincerely, Terry Kuster P.S. Everyone will know about your Web site. Thanks again!

After watching the video that came with the parts, it was straight forward, very well informative.

lid switch was intermittant for awhile befor finnaly quiting..Unplugged machine from elec. then removed four screws on back of instrument/dial panel...lifted the panel and located switch on left side...unplugged switch and removed screw from ground wire..removed switch...ckd part # and ordered part....part arrived on 2nd day after ordering...installed new switch...plugged switch back in..connected ground wire....replaced panel installed four screws... plug machine into receptical and ran a cycle to test. everything working fine.. I tested continuity of the old switch ..it was fine the problem was with the plastic spring that holds the switch in the slot...and allowed it to move thus not allowing the contacts to close. ground wire screw and two of the other screws required a nut driver..the other two crews required a phillips head screwdriver...10-15 min to remove switch and order...less than 10 min to replace switch and put the panel back on. location of my washer allowed me to work on it without moving it...if it is backed up to a wall..it will have to be moved enough to reach the screws on the back.

Used part PS886960. Simple process to replace - removed the two screws and flipped the part that houses the controls/electrical over. The switch was easily accessable. When changing out the switch the wire inside the old connector had previously gotten hot and bonded inside the plastic. Had to use a pair of pliers to separate. Then there was part of the copper piece still stuck in the connector. Used a drill to remove the bonded piece and jammed the two fittings together. Washer is repaired and working fine. Should have taken about 10 minutes to change the switch but required about 30 total.

1. visited web site followed path for symptoms, identified part ordered 2. Dismantled Washer, removed motor, replaced coupling and re-assembled. 3 Tested outside to confirm working order before returning washer to inside location 4. Moved washer back inside.

I followed the step by step instructions on the computer stopping and starting the program as I went. Thanks Partselect

Parts Select is outstanding..They diagnosed the problem quickly..The part was sent within 2 days and we were washing laundry the 3rd afternoon...THANKS!!!!!!

Just watched the video provided by parts select and then went to work. Excellent video. If I had been better mechanically inclined it would have been much faster. Thank You Parts Select! Also fast shipping.