Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ATG175NLW0

ATG175NLW0 Frigidaire Refrigerator - Overview

Get Parts and Repair Help for ATG175NLW0

If you know the refrigerator repair part you need, you can browse the list of all parts on the ATG175NLW0, or you can search by name or part description. You can also find your part by where it is located on the ATG175NLW0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for ATG175NLW0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$13.80

Defrost Timer - 60Hz 120V

Defrost timers are part of the defrost circuit in your refrigerator and freezer. This timer cycles the defrost heater on and off. For every eight hours, the appliance timer will cy...

Order within the next 1 hr and 24 mins and your part ships today!
$97.59

Ice Maker with Cover - 8 Cube

This Frigidaire ice maker includes the ice mold and control device. The ice maker receives water from the water inlet valve and stores water in the ice mold until it freezes. Ice is automatically ejected and the process continues until the storage bucket is full. Your ice maker should be replaced if ice is not being generated, stored, dispensed, or the ice maker has been damaged. Replacing the ice maker is an easy job and only requires a 1/4 inch nut driver. Before you start this repair, make sure your refrigerator is unplugged. For help with this installation, check out the video below.

Order within the next 1 hr and 24 mins and your part ships today!
$103.77

Replacement Ice Maker

This replacement icemaker may also be known as the ice maker assembly and is compatible with your refrigerator/freezer. This assembly replaces the heat-release ice maker unit only....

Order within the next 1 hr and 24 mins and your part ships today!
$46.27

Evaporator Fan Motor Kit

The evaporator fan motor kit is specifically made for your refrigerator to run the evaporator fan in your refrigerator. It is mounted on the center hub and has three lead wire terminals; its shaft has a diameter of 1/8 inches and is 1-1/4 inches long. The function of the evaporator fan motor is that it supplies air to the evaporator coils which then circulate cool air throughout your refrigerator, efficiently keeping your fresh food compartment cold. The tools you will need for this installation include a 1/4 inch nut driver, and a pair of wire strippers. Keep your hands protected during this repair by wearing work gloves.

Order within the next 1 hr and 24 mins and your part ships today!
$6.64

Light Bulb

This OEM 40 watt appliance light bulb is used for some ranges, refrigerators, freezers, and microwaves. Simply locate the existing bulb, unscrew it from its socket, and replace wit...

Order within the next 1 hr and 24 mins and your part ships today!
$7.71

SOCKET

The light socket on your refrigerator houses the light bulb and connects it to the power source. If you notice that your refrigerator light does not come on when you open the door, you may need to replace the light socket. This light socket is made of white plastic with two metal prongs. The light socket is located inside the refrigerator. Many of our customers have rated this repair as easy. To complete this repair, simply pop the old socket out with a small flat blade screwdriver and disconnect the wires. Then simply reconnect the wires to the new socket, and snap it in place with the locking tab.

Order within the next 1 hr and 24 mins and your part ships today!
$15.70

Defrost Thermostat

This limiter thermostat cuts out when the temperature inside your refrigerator reaches 55 degrees Fahrenheit and kicks back in when the internal temperature drops to 20 degrees Fah...

Order within the next 1 hr and 24 mins and your part ships today!
$5.21

Door Shelf End Cap - Left Side

Order within the next 1 hr and 24 mins and your part ships today!
$5.90

Door Shelf End Cap - Right Side

This white end cap is a little over two inches long. It is used for the right side of either the refrigerator of the freezer door shelf.

Order within the next 1 hr and 24 mins and your part ships today!
$43.91

Door Shelf Retainer Bar - Cut to Fit

This is a white cut-to-fit door shelf retainer bar.

Order within the next 1 hr and 24 mins and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Fridge got warm and freezer coils were frosted

  • Customer: Stephen from Warrington, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 295 of 346 people found this instruction helpful
Fridge is a side by side. The freezer is pretty narrow for a guy with wide shoulders.

Pulled plug.

Had to remove bottom drawers then used nut driver to remove screws closest to back wall in drawer runners. Once the back screws were removed the runners could be swung up or down out of way so back cover could be removed.

On... read more

Broken ice maker

  • Customer: Juan from Miami, FL
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 169 of 226 people found this instruction helpful
Unplugged faulty ice maker, removed two screws holding it to the refrigerator and took it out. Reversed the operation with the new ice maker and after a few minutes presto, we have ice. read more

Ice Maker Stopped Working

  • Customer: JACK from MESA, AZ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 129 of 140 people found this instruction helpful
It was pretty straight forward. Remove the two screws that hold the unit to the wall of the freezer. In my case, I had to use a different ice maker than what came with the frig. In order to install the replacement unit they sent a wire adaptor so it would attach to the existing wiring. That too was all fine and dandy. The only problem was that the ... read more