Models > ATF8000FS1 > Instructions

ATF8000FS1 Frigidaire Washer - Instructions

All installation instructions for ATF8000FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF8000FS1
1-15 of 202
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 210 of 249 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 80 of 96 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 66 of 73 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.

Washer would not spin

  • Customer: Keith from Sayville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 62 of 70 people found this instruction helpful
Door lock takes a beating due to flimsy washer door which does not align well and subsequently gets slammed each time which causes lock to malfunction telling the washer that it is not locked. Due to safety the washer will not go into the spin mode. Remove top lid (2 screws) open washer door and loosed the 2 screws holding the lock assembly in place. Reach down into the washer and unsnap the 3 wire harnesses. Reverse to reinstall. Very easy.

Valve dispener would spray water all over inside of washer.

  • Customer: Julie from Lancaster OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 43 of 51 people found this instruction helpful
My husband made the repair. First, he had to remove the dryer off of the top of the washer since it's a stacking unit. Disconnect water lines. Next he removed two screws from the back of the washer that allows you to remove the lid. Now unsnap a trim piece that is on the back surrounding the water connections and an exhaust port. Reach inside the washer, turn the exhaust port unlocking it and pushing out the back of the washer as far as you can to get it out of the way. Disconnect the electrical lines from the valve dispenser. Remove the two screws that fasten the valve dispenser to the washer. Install the new dispenser and reassemble.

Door Striker broken

  • Customer: Susan from Oakland ME
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 35 of 39 people found this instruction helpful
The door striker of the my front loading washing machine is plastic and breaks very easy. The small store I brought it from is now closed and I can't get the part and the last time I did order the part it took a least two weeks for it to arrive and my wash pile was huge. I ordred your part and in two days I had it! Much easier than the 65 dollars charge to have the repairman walk through the door to fix it and the long wait for it to arrive.

After a full cycle the washer would not drain the water

  • Customer: sara from North Miami FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 32 of 34 people found this instruction helpful
After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer worked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.

washer would not go into final fast spin cycle. Clothes would still be extremly wet. When in drain and spin would drain and then spin slowly around 7 minutes left in cycle would shut off.

  • Customer: Toni from Lockport IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 32 of 34 people found this instruction helpful
Using a screw driver I removed the spring loaded band from around the rubber boot inside the door. You only need to remove the band and then pull the boot from the bottom around to the side. You do not need to fully remove boot. Unscrew locking mechanism. Slide out to be able to see connections. Remove connections. Replace mechanism, reattaching connections into appropriate spots. Replace mechanism and rescrew in. Replace rubber boot by pulling gently out and working rubber V of boot under the metal slot. Once the boot is replaced, replace the metal band making sure the spring is at the bottom of the boot. Wahlah!!! Washer is working perfectly.

pump very noisy, failing.

  • Customer: John from Mason MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 26 of 29 people found this instruction helpful
Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

Door lock switch faulty preventing washer from spinning

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 28 of 35 people found this instruction helpful
Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.

Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.

Works like new!

Tub loose

  • Customer: Mel from Ipswich MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 25 of 28 people found this instruction helpful
Take off the back, one of the shock absorbers was broken, it was very obvious. Looked up part at partselect.com, very easy, ordered part, it came in 2 days, the repair took another 15 minutes. There were directions inside the repair part to tell you a trick to get the old one off. It worked like a charm. Why spend $200-300 or more on a repair on a $500 washer when you can do the entire job for about $30 and get it back working in 2 days!! No brainer.

Pice busted off of door striker.

  • Customer: Terrance from Three Lakes WI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 23 of 26 people found this instruction helpful
I just removed the 2 screws, removed the old striker and replaced it with the new one. The entire project took 3 minutes.

discharge of water out of wash machine

  • Customer: William from York Springs PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 21 of 27 people found this instruction helpful
remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry

The washer would not drain

  • Customer: Harry from Zephyrhills FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 17 of 17 people found this instruction helpful
After removing the front of the washer, I used slip joint pliers for the hose clamps, then a screwdriver for the mount bolts and replaced the pump motor in reverse order. The pump was ordered on line on a Friday before 10am and was delivered on saturday moring by FedEx. I could not have expected such fast and efficent service!
Great Job!!

water pump broke

  • Customer: Lili from Jamestwn NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 17 of 19 people found this instruction helpful
My Husband did the repair it took less than 15 minutes. He popped the front off the washer. He then unscrewed two screws and removed the pump assembly. He popped the new pump in, and put in the tow screws. Then he put the washer front back on replacing two screws. It took all of five minutes. I am so pleased it was so easy. I told him next time I'd do the repair and he could watch!
Lil
All Instructions for the ATF8000FS1
1-15 of 202