Models > ATF8000FG1

ATF8000FG1 Frigidaire Washer - Overview

Get Parts and Repair Help for ATF8000FG1

If you know the washer repair part you need, you can browse the list of all parts on the ATF8000FG1, or you can search by name or part description. You can also find your part by where it is located on the ATF8000FG1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ATF8000FG1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$68.60

Door Lock and Switch Assembly

***NOTE: As per the manufacture, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would requir...

$45.43

Shock Absorber Kit

This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.

$49.57

Water Inlet and Dispenser Valve

This part comes with the sensor/thermistor.

$30.82

Door Striker

This part is found on the door of your washer and keeps your door closed for use.

$100.34

Drain Pump - 60Hz 120v

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

$53.14

Door Hinge with Bushings

This part attaches to the outside of the front door panel to help with the door open and closing properly.

$5.27

SCREW

$29.11

Drain Hose

Also known as tub-to-pump drain hose.

$16.73

Spring-Held Bellow Clamp

$33.87

Drive Belt

This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 189 of 225 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 72 of 86 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes l... read more

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 61 of 68 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went w... read more