Models > ATF6700FS1 > Instructions

ATF6700FS1 Frigidaire Washer - Instructions

All installation instructions for ATF6700FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6700FS1
31-45 of 191
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

door assembely had a snapped piece of plastic in unit.

  • Customer: DANIEL from STRATFORD NJ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I released the door gasket and unscrewed the unit .Labeled the connections. then reconnected reattached, then put gasket back on. Worked like a charm!

Water Flooded Floor

  • Customer: Matthew from Weyers Cave VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 10 of 13 people found this instruction helpful
First I took sides off the washer. I then took screws out of the Drain pump holder. Unclamped the two pipes from it. Undid the wires to then drain pump. Screw in the new pump hardware. Plugged in the wires on side of the pump. Reclamped the pipes. Put sides back on washer and it worked. That easy and took less then 30 minutes. I am no handy man so thats how easty it was.

Broken washing machine Vane

  • Customer: Ken from Rhinelander WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 10 of 13 people found this instruction helpful
Totally unable to move old vane using instructions on this site. Wound up breaking old unit in pieces to remove. Installed very easily. However when trying to install enclosed screw (which you are supposed to install through vane into tub) it did not line up even close to hole drilled into tub. I had wondered why the original vane didn't have a screw in it, now I know.

Water not draining

  • Customer: Harold from Denver NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 9 of 11 people found this instruction helpful
It turned out that the pump was fine. There is a filter within the rubber bellows between the washer drum and the motor. You need to remove the entire bellows to get to it. Just remove the motor and you can un-clip the hose tensioners. They are exactly like the ones you would fine on most foreign cars - just compress with pliers and move back on the hose. Clean out the plastic filter. A small nail had worked its way through the plastic filter and lodged in the motor impeller. Removing this nail and reassembling, it all worked as new! I kept the pump and motor as a future spare rather than return it.

locking mechanism spring broke

  • Customer: laura from willow creek CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 10 people found this instruction helpful
Watched video which was very helpful

washer would not spin out

  • Customer: Linda from Dover FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 13 people found this instruction helpful
First called a repairman.Wanted over $300 to put a new door lock assembly in.Searched the web, found PartsSelect,bought part for less than $75,husband did repair in less than 30 min.
VERY happpy customer.

THANKS

Drained but would not spin

  • Customer: Gregory from Louisville KY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 8 of 10 people found this instruction helpful
The hardest part was figuring out how to get the lid off. You simply remove two screws from the back of the lid and jerk and slide the lid towards the back of the machine. Take out the screws that hold the front panel on, tilt the front out and access the lock/switch assembly and replace.

Washing machine wouldn't drain

  • Customer: Siobhain from Ashland NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 7 of 8 people found this instruction helpful
i removed the front panel, then removed the old pump by taking off the clamps and disconnected the wiring. The new pump had to be reversed before connecting, but it was so easy.

Glass inner door cracked due to machine rocking

  • Customer: Gennaro from Nutley NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
Simply removed several screws around inner glass Then part set right into place. replaced all the screws and was completed.

Thumping vibration on spin cycle

  • Customer: Kerry from Pasadena CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 7 of 9 people found this instruction helpful
Remove the front lower panel. Remove the 4 plastic pins mounting the shocks using 1/2 inch short socket to hold the detent down as per included instructions. All plastic pins were stuck in place so used needle nose pliers to pull or push out. Lube the pins with grease before reinstall to help them go through the new shocks. Use the included lock nuts to lock the four legs in place as low as possible. Start the washer and level each leg while running so you can tell if the vibration is going away. Tedious method but worked.

Door lock switch plastic bits broke

  • Customer: Herbert from Amherst NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 7 of 9 people found this instruction helpful
The previous posts made it dead easy - remove screws at the back holding top in place; slide top back; remove screws holding door latch assembly; disconnect three plugs, and connect new part. Replace fastenings, done! Throw up hands and wait for the official time;)

I had tried to clean the small basket type screens at the rear of the inlet valve but both of them disintegrated

  • Customer: George from INMAN SC
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 9 of 15 people found this instruction helpful
Following the instructions on your page I was able to see quite clearly what needed to be done. I received the new part promptly and my machine is now working fine. However, the ongoing story with the dryer is another matter.

Spin Cycle wouldn't work

  • Customer: KEITH from BEND OR
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 7 of 10 people found this instruction helpful
Replaced pump, by removing back panel and removing the two screws holding the pump to the bottom of the machine. The only difficult aspect was dealing with the hose clamps, these were extremely awkward to work with in a confined space. The repair would have been less than 30 min if the hose clamps weren't so difficult to put back in place.

Broken Face Clips on dispenser drawer

  • Customer: david from spring hill FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 7 people found this instruction helpful
I unclipped the old drawer parts from the broken drawer and replaced the old parts onto the new drawer and slid the whole drawer back in the washing machine. It took longer to type this that it did to repair the washer. No tools needed at all.

Original glass broke due to uneven load and drum struck the glass

  • Customer: Dallas from Saint Augustine FL
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
With breakdown maual, I diassembled the door and reinstalled the glass and rehung the door and closed it. Turned on the machine and the bottom of the glass does not meet the rubber seal on the washer opening.
All Instructions for the ATF6700FS1
31-45 of 191