Models > ATF6700FS1 > Instructions

ATF6700FS1 Frigidaire Washer - Instructions

All installation instructions for ATF6700FS1 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6700FS1
136-150 of 204
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Two broken shocks

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Unplug. Remove front lower cover panel. The trick is getting the old pins out and the solution was the alternate method provided in the written instructions that came with the shock kit. Use a deep 13mm or 1/2" socket over the pin end to depress the locking tab. After that, it is just a matter of prying the pins out. I was able to salvage all of my existing pins and the new (different design which will hopefully hold up much better) shocks went in pretty easily. The shock kit was reasonably priced but replacement pin were incredibly overpriced, so I was motivated to salvage the ones installed.

fills but will not spin.

  • Customer: Daniel from Wyoming MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
This is the second part I have put on it and it still does not work. It is now leaking some also. So tonight I replaced it.

Door would not close

  • Customer: Deborah from Keeling VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The latch that held the door broke off, and of course the washer would not work , I called around locally and the small part price was outrageous,I went on line and found Pats select,and the price of the part was 1/3 of the cost locally I order the part and even with next day delivery I saved money from buying it locally

The drain house was penetrated by a piece of metal from coin catcher

  • Customer: Kimberly from East Moriches NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I took off the face and top of washer changed the drain hose.and put it back together and it started leaking .word to the wise. mmake sure the back side of the drain hose that is not visable is all the way on then tighten.

Excessive vibration

  • Customer: William D. from Sanford FL
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
Took the back off the machine. pulled out the old shocks and installed the new. Put the back on. Simple

Washer would drain most the time but not spin

  • Customer: Johnny from Providence NC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This is a front loader and the video I saw was a top loader. I removed the oval shaped centerpiece off the back to reach the pump. I also removed the filter and cleaned it, I used screw type hoseclamp in place of the tension spring for easier assembly due to the cramped space. This helped the drain problem as did cleaning the filter. The no spin problem persisted and I ordered the door lock part. This part fixed the no spin problem.

broken shock

  • Customer: Tracy from Mammoth Lakes CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
the existing pin was in backwards and to get it out was a problem because there was not enough room behind the pin to get it out.also i thiugh there was 2 pins in the kit and there was only one.

Washer would drain, but not spin

  • Customer: Tom from Atascadero CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Removed two screws on the back of the washer top to release the top on the washer. Slid the top off and removed it. Opened washer door and removed two screws securing the door lock assembly to the washer frame. Reached in from the top of the washer to get the door lock assembly. Unplugged the old door lock assembly in three places and plugged the new assembly in in the same three places. Placed the new assembly in the same place as the old one and secured it to the washer frame with the same two screws located on the inside of the door. Replaced washer top and secured two screws at the top back edge of the washer... Tried the spin mode and everything worked great!!!

The cold water valve was not closing completely and the tub would fill will water after several hours.

  • Customer: Eugene from Crestwood MO
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I shut off the water supply and started a cycle to release the pressure on the valves. Unplugged the power. Removed the top by unscrewing two screws on the back. Unscrewed the water lines and snapped off the plastic retainer for the water lines and overflow tube. Disconnected the wires to the red, green and blue valves, as well as the small black sensor on the side of the valve assembly. I had to unlock and partially disconnect the overflow tube to allow me access to one of the mounting screws. Removed the other mounting screw and separated the valve assembly by pulling it firmly. I put a little silicone grease on the two rubber mounting grommets and inserted the new valve assembly and re-assembled screws, wire harnesses. Replaced the top and screwed it down.

Not Draing Water

  • Customer: Sammy from Notasulga AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Good

both shocks on drum was broke.

  • Customer: Kenneth from Effingham SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Took cover off bottem on front of washer and pulled pins out of shocks. Put new shocks in and put the pins back in and reinstalled the cover. It was a easly fix and looking up the parts needed and ordering them was made easy by PartSelect.

Washer Stuck in Pause Cycle

  • Customer: D. Patrick from Vacherie LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The door assembly did not fix the problem this time, it was the control panel that had to be replaced. I have replaced the door assembly in the past, and I am glad I have a spare on hand. They do go out over time from the pressure of large batches of clothes. I am "no repair man", but having someone come out to replace it for you is a $300.00 job, easily. Read the tech info for your error code and go from there.

door wouldnt stay locked during cycle

  • Customer: Phil from sun lakes AZ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
took the top off removed the old one and put in the new one.Works great!!

broken suspension spring on side load washing machine

  • Customer: Jared from Spanish Fork UT
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I found you web site online found the broken part. I was pleased with a timely delivery and the correct part. A $30 dollar part from you saved me at least $150 from a appliance repairman. Thanks - Jared

Washer pump out

  • Customer: Dorothy from San Antonio TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Was so easy the video link made it even easier. Will with no doubt return for any other problems for my appliances if needed.
All Instructions for the ATF6700FS1
136-150 of 204