Models > ATF6700FE0

ATF6700FE0 Frigidaire Washer - Overview

Get Parts and Repair Help for ATF6700FE0

If you know the washer repair part you need, you can browse the list of all parts on the ATF6700FE0, or you can search by name or part description. You can also find your part by where it is located on the ATF6700FE0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for ATF6700FE0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$74.05

Door Lock and Switch Assembly

NOTE: As per the manufacture, some models require a new wire harness and a door strike for this door lock assembly to work on the appliance. The original style lock would require t...

$34.29

Shock Absorber Kit

This kit is used for front load washers and includes 2 dual-stage shock absorbers, 1 spare shock mounting pin and 4 locking nuts. These shock absorbers keep the washer from vigorous shaking during it's cycles.

$37.05

Door Striker

This part is found on the door of your washer and keeps your door closed for use.

$108.17

Drain Pump - 120V 60 Hz

The pump is what your washer uses to remove the water from the tub. This part is the pump and motor assembly which includes the red flapper to prevent drain back flow.

$53.73

Water Inlet and Dispenser Valve

This part comes with the sensor/thermistor.

$63.64

Door Hinge with Bushings

This part attaches to the outside of the front door panel to help with the door open and closing properly.

$172.89

Bellow Kit

Also known as a Door Boot Seal and is used in front load washers. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub ...

$5.50

SCREW

$17.38

Spring-Held Bellow Clamp

$30.25

Drain Hose

Also known as tub-to-pump drain hose.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 245 of 290 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections. read more

Old Bellow Ripped

  • Customer: Peggy from New Castle PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 151 of 209 people found this instruction helpful
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside ... read more

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 90 of 97 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went w... read more