Models > ATF6000ES0 > Instructions

ATF6000ES0 Frigidaire Washer - Instructions

All installation instructions for ATF6000ES0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF6000ES0
1-15 of 216
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Broken Door Catch

  • Customer: Joy from Columbia MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 466 of 464 people found this instruction helpful
This was one of the simpliest repairs I have ever done taking less than 5 minutes to complete. On the inner door I removed the two screws that hold the plastic catch in place. I then removed the broken catch and put the new catch in place. Finally I replaced the two screws that hold the catch in place and it was done.

Door on washer wouldn't lock or start

  • Customer: DOUG from KING FERRY NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 187 of 223 people found this instruction helpful
1. Unplug unit.
2. Unscrew 2 nuts holding top in place in rear of unit using phillips head screwdriver.
3.Slide top back and remove.
4. Open door of washer and unscrew 2 screws holding in door lock unit.
5.Pull out unit from the top and install new unit reconnecting the 3 wire connections.

Old Bellow Ripped

  • Customer: Peggy from New Castle PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 127 of 172 people found this instruction helpful
remove top of machine by removing 3 screws along the top edge in the back of your machine and then sliding the top back and up. Then loosen the screws holding on the control panel enough to get to the 2 screws at the top of the door panel. Next remove bottom panel by removing 2 screws along bottom edge then pulling it free from snaps. Then along the outside lip of the bellow, just inside the door, is a wire clip that is easily removed by prying it past rubber lip with a screw driver and lifting it away. Remove the door panel by removing the 2 screws you exposed by loosening the control panel and 2 more along the bottom that were exposed when removing bottom panel. After the door panel is removed and the bellow is completely exposed, you will find that it is held in place by a circular spring which wraps the whole way around the drum opening. Again it can be removed by prying it out away from the groove in which it sits with a screw driver. Now your machine is broken down as far as it needs to be. From here you can follow the directions included in your new bellow kit and put it back together by following these instructions in reverse.

would't spin all water out or rinse out clothes

  • Customer: kenneth from willard OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 72 of 86 people found this instruction helpful
uplugged washer took front off washer 2 screws pryed up top pump was mounted with 2 screws and 2 wires took off found change in pump and the fins to pump worn off ordered part off line the wait for part was longer than the amount of time to fix problem and cost of part saved me about $25-35 if I was to buy local worth wait save money and fix problem washes like new spins and drains all water from tub.

Washer would not spin

  • Customer: Keith from Sayville NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 60 of 66 people found this instruction helpful
Door lock takes a beating due to flimsy washer door which does not align well and subsequently gets slammed each time which causes lock to malfunction telling the washer that it is not locked. Due to safety the washer will not go into the spin mode. Remove top lid (2 screws) open washer door and loosed the 2 screws holding the lock assembly in place. Reach down into the washer and unsnap the 3 wire harnesses. Reverse to reinstall. Very easy.

Both vibration shock absorbers broken

  • Customer: Douglas from Medical Lake WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 60 of 67 people found this instruction helpful
removed 2 screws and removed top access cover. removed 2 screws and removed front access cover. removed 4 retaining pins (one with nammer and punch because it was stuck) connected lower ends of new shocks with plastic pins, extended each shock to slip fit and connected upper ends to wash tub mounts. Reinstalled panels. I wish I could say that it all went well from there but......when the shocks broke, apparently the hit the motor took was enough to cause an electronic failure of the speed cycle control chip. Now Im waiting for that part.

washing machine front loader door would not close, making the machine useless

  • Customer: Susan from Vero Beach FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 56 of 66 people found this instruction helpful
I removed the broken door catch, which consisted of removing two screws, making it a snap to do, all you needed was a screw driver, and replaced it with the new one using the same screws, This took about 5 mins. to do and was very simple. Turning the machine into a working washer again. : )
After looking all over for the part,and not finding it I was thrilled when you carried the part. Even though the machine is old, it works great. Thank you for the selection of all the parts you carry and how you make it so easy for us to find what we need. , and having it in stock, which was mailed right away, so I could replace the catch and have the washer back in use in less than a week. Thank you

Valve dispener would spray water all over inside of washer.

  • Customer: Julie from Lancaster OH
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 39 of 47 people found this instruction helpful
My husband made the repair. First, he had to remove the dryer off of the top of the washer since it's a stacking unit. Disconnect water lines. Next he removed two screws from the back of the washer that allows you to remove the lid. Now unsnap a trim piece that is on the back surrounding the water connections and an exhaust port. Reach inside the washer, turn the exhaust port unlocking it and pushing out the back of the washer as far as you can to get it out of the way. Disconnect the electrical lines from the valve dispenser. Remove the two screws that fasten the valve dispenser to the washer. Install the new dispenser and reassemble.

originall shock was broken

  • Customer: Richard from Quincy MA
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 31 of 33 people found this instruction helpful
disconnected the power and water supply.

removed the back panel.

unscrewed the contol board that blocked access to the bottom of the shock absorber.

pulled the original pins out with pliers while pressing in the piece that prevents it from working its way out.

removed the shock absorber.

placed the new shock absorber in the bottom mount, put soap on the pin for lubrication and pushed it through the hole. Put the top of the shock absorber in its place and placed the other pin in.

replaced the control board and replaced the rear panel.

After a full cycle the washer would not drain the water

  • Customer: sara from North Miami FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 28 of 30 people found this instruction helpful
After reading the possiblilities of problem, I determined that the drain pump was not working; therefore I ordered a new one. When I opened the washer to replace the part, I found out that the pump was working but the filter was stuffed with pieces of rubber that came out from a rug I washed. Once all the stuff was removed, the washer worked just fine. PartSelect was very gracious to accept the returned with not questions asked!! Thanks partSelect.

washer would not go into final fast spin cycle. Clothes would still be extremly wet. When in drain and spin would drain and then spin slowly around 7 minutes left in cycle would shut off.

  • Customer: Toni from Lockport IL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 28 of 30 people found this instruction helpful
Using a screw driver I removed the spring loaded band from around the rubber boot inside the door. You only need to remove the band and then pull the boot from the bottom around to the side. You do not need to fully remove boot. Unscrew locking mechanism. Slide out to be able to see connections. Remove connections. Replace mechanism, reattaching connections into appropriate spots. Replace mechanism and rescrew in. Replace rubber boot by pulling gently out and working rubber V of boot under the metal slot. Once the boot is replaced, replace the metal band making sure the spring is at the bottom of the boot. Wahlah!!! Washer is working perfectly.

Door lock switch faulty preventing washer from spinning

  • Customer: Jeff from Thousand Oaks CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 27 of 33 people found this instruction helpful
Codes did not point directly to the door lock, so that was a 50/50 between door lock and control board. With top of washer removed door lock is just a couple screws and 3 electrical connections.

Belt was worn and frayed. Belt replacement was tricky because new belt was so tight. Used vice grips to lightly hold belt on pulley while using screwdriver through spokes into tub back to ratchet/control pulley. Not too bad.

Works like new!

Tub loose

  • Customer: Mel from Ipswich MA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 25 of 28 people found this instruction helpful
Take off the back, one of the shock absorbers was broken, it was very obvious. Looked up part at partselect.com, very easy, ordered part, it came in 2 days, the repair took another 15 minutes. There were directions inside the repair part to tell you a trick to get the old one off. It worked like a charm. Why spend $200-300 or more on a repair on a $500 washer when you can do the entire job for about $30 and get it back working in 2 days!! No brainer.

pump very noisy, failing.

  • Customer: John from Mason MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 23 of 26 people found this instruction helpful
Disconnect water and electricity.
Shop-vac out the water in the internal drain hose.
Remove back cover, tip washer on side to gain access.
Un-clamp rubber drain hose,unscrew pump and remove.
Cleanout filter cup (yuk!) find coins and hairpins.
Attach drain hose to new pump and re-install with hose clamps from hardware store because spring clamps were impossible (arthritis in fingers).
Reconnect water and electricity.
Test for leaks and tighten clamps if necessary.

discharge of water out of wash machine

  • Customer: William from York Springs PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 21 of 26 people found this instruction helpful
remove side panel & start rinse cycle & heard a grinding noise in discharge pump. used a bucket to catch water upon removeal of discharge hose to pump. unplug disconnect plug to motor, remove pump from unit. Discovered propeller was loose in housing. Googled Partselect.com, odered part & in 2 days later installed new pump on unit. Started a load of wash & it has been working perfect ever since. thanks to PartSelect.com for the service, the repair was minimal & easy for the DO IT YOURSELFER. Bill Starry
All Instructions for the ATF6000ES0
1-15 of 216