Models > ATF2110DRW > Instructions

ATF2110DRW Admiral Refrigerator - Instructions

All installation instructions for ATF2110DRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF2110DRW
391-405 of 491
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The ice in the ice maker would freeze into a solid block. Upon inspection I realized the ice maker was leaking water into the ice holder which was then freezing solid. Three tray for the ice maker was slightly rusted and caused the water to drip.

  • Customer: sal from lighthouse point FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I watched the video on how to change the ice maker, very easily explained, and removed the old in about 10 minutes.After seeing how the old one came out it only took five minutes to install the new one. The appliance repaircompany wanted$120 just to diagnose the problem,i bought the part from partselect for$104 total. This is the forth time I've used this site and saved a ton of money.

Condensor motor was frozen

  • Customer: john from thibodaux LA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip the insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.

ICE MAKER--NO ICE

  • Customer: ALTON from POQUOSON VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
DISCONNECTED POWER--REMOVED ICE HOLDER TRAY--REMOVED ICE MAKER END CAP--DISCONNECTED ELECTRICAL WIRES--REMOVED ONE SCREW HOLDING ICE MAKER TO REFRIGERATOR--LIFTED UP ON ICE MAKER TO REMOVE IT FROM TWO HOLDERS--TOOK CONTROL WIRE FROM OLD ICEMAKER AND INSTALLED IT ON NEW ONE--REINSTALLED NEW ICEMAKER IN REVERSE ORDER.

Icemaker making a clicking noise not dumping ice.

  • Customer: RICHARD from COLORADO SPRINGS CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

ice maker would not cycle. coating on ice tray was flaking

  • Customer: william from marydel DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

Ice maker was producing large wet clumps

  • Customer: Edmund from Fallbrook CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

Ice maker was leaking into the cube tray

  • Customer: Richard from South Lyon MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.

Broken Kickplate Grille

  • Customer: James from Fort Wayne IN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The kickplate grille is a plastic part which has two metal clips attached to it. The old plastic frame had broken free of the metal clips and fallen off the refrigerator. Step One: Removed the two old clips by pulling them out of the refrigerator frame. Did it with finger pressure. 2. Pressed the new part which has clips attached to it into the holes in which the old clips had been placed. Voila, the repair was finished.

Freezer evaporator coil freezing up

  • Customer: Fred from Concord NH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
powered off, removed contents and shelving from freezer, using nutdriver removed 4 screws holding cover in rear of freezer, lifted cover from bottom and slid towards front, unplugged 2 wire leads from fan motor, unplugged wiring harness top left at plug and removed cover, unplugged 2 leads on clip-on defrost thermostat and removed from copper tubing, replaced with new part in reverse order, unplugged wire lead on left and right side of evaporator coil leading to defrost heater, slid out left side of evaporator coil carefully and unfastened clip from defrost heater, rotated up right side defrost heater and removed element, attached clips to new defrost heater and installed in reverse order, attached left and right wire leads, plugged in fan motor leads and wiring harness, replaced cover tilting top to front and sliding in bottom first. installed 4 screws, replaced shelving and powered on. within 3 hours freezer was 0 degrees, fridge 39 degrees, replaced shelving and contents.

broken crisper drawer mount

  • Customer: lloyd from california KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old mount with allen wrench replaced with new mount

ice maker stopped making ice

  • Customer: George from Winhall VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Partselect was great, but I "Gilligan-ed" on the fix changing both the icemaker AND water feed solenoid, BEFORE determining the white rubber water feeder tube that installs from back of fridge and feeds ice maker tray inside of freezer was frozen/ blocked. Make sure you check this FIRST, by proding a screw driver up the tube inside freezer and/ or pulling feeder tube out from back of fridge. If the blockage is substantial enough, it will make removal difficult until melts and tube contracts. Good luck!!

light switch sticking

  • Customer: Paula from Rush NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

Light did not come on (bad bulb!) on TC18KL

  • Customer: Louis from Beloit WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

Freezer continually had ice build up

  • Customer: James from Traverse City MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replacement would have been easy except there was so much ice built up inside the door. Should have just turned it off for 48 hours to let ice melt. Instead completely disassembled door to remove ice.
All Instructions for the ATF2110DRW
391-405 of 491