Models > ATF1910DRW > Instructions

ATF1910DRW Admiral Refrigerator - Instructions

All installation instructions for ATF1910DRW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ATF1910DRW
391-405 of 512
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker making a clicking noise not dumping ice.

  • Customer: RICHARD from COLORADO SPRINGS CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Rmoval and replacement is not at all complicated. (1)Reach behind and to the left of the icemaker and release the power plug. There is a release snap on th side of the plug. (2)Using a 1/4" nut driver remove the screw holding the icemaker to the "L" bracket at the bottom of the icemaker. (3)Using the nut driver loosen two self taping screws holding the top of the icemaker to the side of the freezer compartment.(4)Lift up on the icemaker to remove it. (5)remove the white plastic cover from the front of the icemaker (pry out at the bottom) and snap it onto the new icemaker. (6)Remove the wire sensor arm from the old icemaker and place it on the new one. (7) Remove the cable assembly (plug) from the old icemaker and fasten it to the new one. (8)Secure the new icemaker in place using the reverse order as the removal. The icemaker will take a little longer to make its first batch of ice as it will have to attain its proper operating temp (0 degrees to 2 degrees F).

Light bulb failure

  • Customer: Grant from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

ice maker would not cycle. coating on ice tray was flaking

  • Customer: william from marydel DE
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Since I had more than one issue, I decided to replace the entire ice maker. All I needed was a nut driver and it took 5 minutes. Three hex screws and unplug the wire harness and the whole unit came out. I changed the harness over and installed the new unit. I left for work and came home to ICE. It was Great!!!

Ice maker was producing large wet clumps

  • Customer: Edmund from Fallbrook CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
1. Viewed the video furnished (very helpful) 2. Turned off circuit breaker (avoids having to move the refrigerator), took my chances and left the water on 3. Removed the ice bin 4. Removed bottom retention screw, loosened the top two screws 5. Lifted the old ice maker free of top two screws 6. Used the bright flashlight to see how to release the rear electrical connection 7. Placed old unit on toweling, removed the electrical harness, the bail and the lower retention offset bracket (needed because the Kenmore's bottom retention is toward the center of the ice maker) and reinstalled them on new unit, taking care to maintain the original harness clip method 8. Carried the new unit to the refrig and installed the rear harness connector, then lifted it to mount on the top screws, forced it down to correct position, installed lower screw and tightened all three. 9. Placed bail in 'Operate' position, Installed bin and turned on the power. 10. Next morning, success!

Ice maker was leaking into the cube tray

  • Customer: Richard from South Lyon MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Once I received the new icemaker, I removed the old one by loosening the two upper screws and removing the lower. The wire connector came out easily. The wire and the bale from the old unit had to be transferred to the new unit. Then the new unit was reinstalled and the wire plugged back in. It took several hours for the cubes to begin dropping.

broken crisper drawer mount

  • Customer: lloyd from california KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed old mount with allen wrench replaced with new mount

ice maker stopped making ice

  • Customer: George from Winhall VT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Partselect was great, but I "Gilligan-ed" on the fix changing both the icemaker AND water feed solenoid, BEFORE determining the white rubber water feeder tube that installs from back of fridge and feeds ice maker tray inside of freezer was frozen/ blocked. Make sure you check this FIRST, by proding a screw driver up the tube inside freezer and/ or pulling feeder tube out from back of fridge. If the blockage is substantial enough, it will make removal difficult until melts and tube contracts. Good luck!!

light switch sticking

  • Customer: Paula from Rush NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.

Light did not come on (bad bulb!) on TC18KL

  • Customer: Louis from Beloit WI
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.

not made ice

  • Customer: Sunny from RICHARDSON TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
The part came in 5 days from time order. take less then 10 minute done. part work well, have ices again, Thank you Part Select. we don't have to buy a new Rerigerator

Ice maker not making ice

  • Customer: Warren from Houma LA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I started by changing the water inlet valve. It made one batch but it did not eject into the ben. I removed the ice maker and found that the coating inside was bad. I changed out the ice maker and it is now making lots of ice.

Not making ice

  • Customer: Raymond from Hanover Township PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I went on line and viewed the video. It looked so easy I ordered the new ice maker. Having the information I was able to take apart the old one and view the problem. By the time the new part arrived I was experienced with the installation. I was shocked when the new ice maker arrived within 1 day. I completed the installation without a hitch, I was delighted with the ease of installation and the operation of the new iace maker.Thanks again...Ray

Ice maker quit

  • Customer: Peter from Johannesburg MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed contents of freezer as this was a bottom unit. I had to remove freezer drawers/door to easily access ice maker which was located in the back of unit,wasnt a problem.I did however take a hair dryer to water tube as it froze up with about an 6 inch tube of ice that finally slid down. Connected unit and had ice within an hour or so and a full tray within 24 hrs. Second ice maker in little over a year...Video very helpful, saved 100 bucks by doing myself. Part arrived fast, great job!

Ice maker leaked a little, then quit completely.

  • Customer: Steve from Lansing MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We ordered a PartSelect PS2121513 ice maker. I was concerned that there was no instructions shipped with the unit. Fortunately, PartSelect had an online video that guided me through the process. It wasn't that complex really. The only time I felt totally dumb was when using my nut driver to remove the bottom bracket. I couldn't figure out why there was no 1/4" socket with my set, so I used a small socket wrench instead. I finally figured out that the driver was already a 1/4", without a socket in it. After that it was easy. Slid the ice maker up a little to free it from the top mounting screws. Pulled it outward a bit to gain access to the connector at the back of the freezer, then squeezed the two sides of the connector and out it came. I popped the plastic cover off the existing device and then removed the connector as instructed in the video. I also removed the bale (as per the video). I put the connector harness, plastic cover and bale on the new ice maker and put it back in, this time using the nut driver on the bottom bracket :-). My only concern after that was that it didn't seem to be working. I had no idea that it needed some time to get cold before it would work. After about an hour, it filled with water and began making ice. Success.

Ice maker water level was overflowing.

  • Customer: Brian R from Rockwall TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I followed the repair instructions the Part Select site provided for this replacement valve. The only differences were I needed a small socket/wrench set in place of screw drivers.
All Instructions for the ATF1910DRW
391-405 of 512