ATB2112ARW Admiral Refrigerator - Instructions

Video was helpful and reading the other responses online was a big help also. Followed all of those instructions. Most difficult part was disconnecting the electrical plug to the ice maker. Need a screwdrive or other pointed object to depress plastic tab. Other than that, things went smoothly. HOWEVER, after turning water back on and plugging in fridge, I thought everthing was perfect...no leaks initially. BUT, came back a few hours later to find no ice cubes in the holding tray, "iceburg" formations and ice dams built up again thoughout the freezer. Water was leaking continuously from the ice maker. Upon further analysis, it appears the electronic mechanism keeps telling the fridge to send water to the ice maker...or, it is sending too much before shutting the water off. The tray is overflowing and that seems to be the problem. I'm back to square one, but with a new ice maker.

Quickly after video

Watched the video on the web site and then followed the instructions. It was very easy to change. After changing it, I filled it with water from a cup to get it started making ice since the video does not address how to do this. It has been working well ever since. If you are handy with tools, you can do this.

I put in a new ice maker because it was not in very good condition. The water valve had a very slow leak which allowed water to freeze on the way to the ice maker and plugged the line. This problem was in one of your repair articles all of which were very welcome

I had to replace the whole unit. The tray should have lasted longer and there should have been a replacement tray available.The installation was easy. 3 screws removed, unplug unit, turn off water and put in new unit.

Sorry for delay in writing. Part I ordered arrived two days ago and it was exactly what I needed. Knowing that there will be problems even with the smallest job I procrastinated starting. When I did start this morning I foud I had to completely remove the ice maker and disassemble it in order to install the water fill cup bracket. The challenge was reassembling the unit. Not hard for an experienced repairman but a challenge for layman. Everything is thing is back to gether now and power on cooling down the refrigerator. Won't know how successful it was until turn on water and ice is formed. If it works this saved $75 just to get a Sears repairman to come out and tell me what would be needed to fix the refrigerator and $1,000 if I had to buy a new refrigerator. Extremely satisfied with service I received. Thank you.

Removed the freezer door and replaced with the new hinge.

I turned off the water and electricity to the refrigerator. Then I removed the ice bin exposing the ice maker. I loosened the two screws on the wall with a 1/4" nutdriver and I removed the horizontal screw on the bottom of the ice maker again with the nut driver. That allowed me to lift off the ice maker so that I could remove the wiring harness from the ice maker. A flat screwdriver helped me push in the retaining tab, and disengage the harness. Installation was in the reverse order. A third hand would have helped reconnect the wiring harness, but I put a shoe box on the top shelf of the freezer compartment to hold the new unit while I connected the wiring harness, making sure to "hear it click" when fully engaged. I then removed the wire "feeler" from the old unit and inserted it in the new one. Inserting the water inlet hose and hanging the ice maker was simple after that. The existing bracket holding the ice maker on the bottom was not rusted so I did not replace it even though a new one came with the ice maker. I should add that I had previously defrosted the freezer in order to remove the ice bin as it could not be removed with the block of ice that had frozen in the front end. I'm a senior citizen with no prior experience in changing an ice maker. I wasn't trying to set an amount of time it could take which was about 40 minutes, including the time it took to turn off/on the water and electric breaker and go to the garage for a flat screwdriver and find the right size nutdriver, and next time I could probably do the job in about 20 to 30 minutes! Bob I. San Diego, CA

Removed bad motor with socket set and pliers then removed the connectors from the old motor and soldered them on the new one. Then installed new motor. Works like new! Problem Solved! Easy fix!

This refrigerator has the freezer on the bottom. You have to remove both of the drawers to get to the icemakeer. I did not disconnect the water line or the power to the unit because it is a hassle to pull the unit out of the hole where it resides. I first unplugged the power from the icemaker to the unit and used a flat tip screwdriver to get the icemaker out. The old one was gross. We had noticed flakes in the ice for over a year but thought it was the water. The wire bar from to stop making ice had to be moved from the old icemaker to the new one as well as a brace on the bottom of the icemaker and the front cover. This is all easy. The hardest part of the repair was getting the larger drawer back on its guide. Honestly, this was a repair my 11 yr old grandson could have done with some supervision. I'm guessing I easily saved $100 by repairing this myself.

Extremly easy - just followed the video exactly. Changing the ice make out couldn't have been more easy. when the ice maker was out - noticed some ice build up in the filling water tube. Used the hair dryer to defrost (will replace the double outlet water valve to stop this once my husband is there to help me pull out the frig.) We now have perfect ice cubes. still slowly having issues with some ice build up - but know the water valve is bad too. more to come!!

replaced ice maker, followed the on line video instructions and it was the easied repair i've ever made it took less then 15 minutes

The replacement ice maker was exactly the same size and model. All the mounting screws lined up and install was snap. The website parts description was very good and helpful. We now have ice cubes with no over flowing glacier in the ice tray.

Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.