Models > AT21M8FA

AT21M8FA Admiral Refrigerator - Overview

Get Parts and Repair Help for AT21M8FA

If you know the refrigerator repair part you need, you can browse the list of all parts on the AT21M8FA, or you can search by name or part description. You can also find your part by where it is located on the AT21M8FA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your refrigerator. We’ve also included any installation videos we have for AT21M8FA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$107.31

Replacement Ice Maker

NOTE: This replacement ice maker mechanism does NOT come with a cover,shut off arm, a wire harness, or the mounting hardware. Must be ordered separately.

$2.52

Light Bulb - 40W

Sold individually.

$15.44

Capicitor

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer.

$2.70

Screw

Sold individually.

$30.70

Condenser Fan Motor Kit

This condenser fan motor operates in a clockwise fashion and carries carries 2W and 115V. It comes with screws, a blade mounting nut, and a cushion. This part provides forced-air ...

$2.70

Screw

This screw is sold individually.

$6.98

Light Rocker Switch

$14.89

Water Fill Cup and Bearing

$2.03

Screw with Washer

This metallic screw is less than an inch long and comes with a plastic washer.

$55.91

Defrost Timer

This refrigerator defrost timer will cycle for twenty-one minutes after every ten hours of run time. The defrost timer acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Icemaker producing few or no cubes and often leaving "kling-ons" on ice tray

  • Customer: Bernie from Diamond Bar CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 517 of 529 people found this instruction helpful
Interior surface of ice tray felt rough & flaky (coating deteriorated) so cubes would not release.
Unplug appliance.
Remove timer cover by hand pressure @ edge.
Remove single attachment screw & bracket at lower front of icemaker.
Disconnect wiring harness from socket @ rear of compartment.
Tricky part was determining what type of con... read more

Water overflowed ice maker turnning ice bucket into solid mass of ice

  • Customer: Harry from Grand Ledge MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 205 of 276 people found this instruction helpful
My ice maker has been shedding its non-stick coating for over a year. Within the last month of so, it started pouring water into the ice bucket below, turning it into a solid mass of ice. So I purchased a new ice maker assembly. I encountered two problems not mentioned in the 21 or so do-it-yourselfer repair stories that precede this one. First problem: o... read more

My refrigerator stopped cooling and the freezer section stopped freezing

  • Customer: garth from forest lake MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 110 of 120 people found this instruction helpful
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck let's give her a shot ... read more