Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ASD2522VRW00 > Instructions

ASD2522VRW00 Amana Refrigerator - Instructions

All installation instructions for ASD2522VRW00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ASD2522VRW00
571-585 of 952
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

freezer stopped making ice

  • Customer: Robert from Shenandoah, TX
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Took 1/4" nutdriver and loosened the two screws on top then removed the one screw underneath. It came out except for the wiring harness attached. My icemaker came with a wiring harness, but I elected to unsnap and use the one in the freezer to keep from doing more work on connection. Replaced the bail and heard the first ice drop in a couple of hours, then more ice till it was full the next day.

Ice making stopped working

  • Customer: Kimberly from Harrisburg, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Easily installed the part on Tuesday night. Had ice by Wed morning.

Ice maker was leaking

  • Customer: Richard from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Turn off power & water, using a nut driver removed lower screw, loosen the 2 top screws. Lifted unit up and out a little to remove power cable. Removed lever and installed on new unit. Hooked up power cable install it over the 2 top screws, install bottom screw and tighten all 3. Turn on power and water, lowered bar. It started making ice in about an hour. NO LEAKS. Did not have to adjust water level. Took me less than ten min to complete.

would not make ice

  • Customer: Charles from Chappells, SC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
old icemaker, took out bottom screw, loosened top 2 screws (do not take out) lift and lay down, take off front cover, a little clip will let you disconnect power cord. take old icemaker out of fridge. take off the wire to lift to cut off ice and put on new icemaker. plug power into new icemaker and hang on top screws. wait about 45 mins. and the new icemaker will make a cycle with no water or ice. at this point the new icemaker will fill with water and damn in about an hour or hour and a half you have ice. Oh, don't forget to put the ice bucket back in freezer. now tighten top screws. haven't put bottom screw back in yet.

Stopped making ice.

  • Customer: Allen from Oakwood Village, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I removed the ice maker, researched the part number and ordered the part. I followed the instructions and Iinstalled the part.

The ice maker quit making ice.

  • Customer: Joby from Pasadena, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The installation could not have been any easier. First you will want to turn off the water supply and unplug the refrigerator. Next remove any shelves that are in the way of removing the old unit. Then you will remove the single 1/4" screw at the bottom of the unit completely and then loosen the 2 at the top (leave them in place as the ice maker sets down onto them). Next lift old ice make up and unplug the wiring from it. Finally reverse the process. It is worth mentioning that was forced to reuse the existing wiring harness as the old one was hard wired to the refrigerator. This presented no problem as the new ice maker is making ice .

Ice Maker stopped working. Only 4 months old - installed by Sears

  • Customer: Theodore from Garden Grove, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Messed with trying to get cable assembly plugged in for most of an hour. Finally swapped cable assembly with the old one. Plugged right in. Finished in 20 minutes.

my ice maker had stopped producing ice.

  • Customer: Carol from Eatonton, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I received my new ice maker and got a nut driver and went to the freezer and removed my old ice maker . Then I noticed a problem. The cord on my old ice maker did not have a plug in the middle, my wires seemed to go through the wall of the freezer. I was afraid I would damage it if I tried to pull the wires from the wall, so I called customer service . She said I apparently ordered the wrong part. I had order a $70 unit and she said I needed the $114 kit. I would have to return the unit and order the kit. But she told me to look at the kit description and watch the repair video to see if that would help to see if I thought I could do it myself or get a service person. After looking at the parts and video I realized that the kit would be sending me the exact same unit and a couple of different type wire cords. I decided that all I needed to do was use the wire harness from my freezer and remove the new wire harness from the new ice maker unit. Of course I cut off the power to the refrigerator before pulling the plugs.I just had to loosen the two upper screws and remove the bottom screws, pull out the old unit, unplug the wire harness from the ice maker and removed the new wire harness from the new unit. Then I plugged the old wire into the new unit, slipped the unit back into position being certain that the water tube was in the proper position, tightened the upper screws, replaced the lower screw. I turned the power back on and waited. In a while I had ice again.

Ice maker would not make ice. short fill & plastic gear slipping and locking up.

  • Customer: warren from hammond, IN
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
trip breaker. remove and save cover. loosen 2 top screws & remove bottom support bracket. unit slides up and out. unplug wire harness . attach new unit to wire harness. slip new unit in clearing fill spout. attach bottom support bracket and tighten top screws. replace cover and set breaker. CREATE REAL ICE!!

ice maker quit working

  • Customer: johnny from haysi, VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I took out three screws and unhooked the wireing harness and lifted out and put the new one in put back the three screws and it took the ice maker 24 hours before it would do any thing. it wokrs but very slow making ice.dumps one tray full every 12 hours. works very slow.

No Ice cubes

  • Customer: Tom from Mears, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Loosen 2 quarter inch screws on top side and remove one on bottom of ice maker lower unit disconnect wiring harness install new unit and tested Great Very easy thing to do didn't need instructions. Unit is working like new. Easy to search for parts on your web site

IceMarker wouldn't make ice

  • Customer: Jon from Laveen, AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Unscrewed one screw under icemaker and the two screws above, pulled out old icemaker unhooked power cord attached cord to new icemaker replaced screws and attached bail wire from old to new pluged in the refrigerator and icemaker started making ice, took about 30 minutes before first ice dropped into ice holder.

Ice Maker was leaking from ice tray

  • Customer: Paul from Punta Gorda, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Shut off Water and Electricity. Took out the Ice Bin. Removed one bottom hex nut and then loosened top-side hex nuts (don't remove them, just loosen them) the Ice maker will slide onto the hex nuts on the side of the refrigerator.Disconnected the wiring harness from the maker. Put everything back in reverse order and Bingo! No leaks and lots of Ice.

couldnt use ice maker dispencer. ice melting and leaking

  • Customer: Kevin from Wyandotte, MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed (snap on)removed screw, and ice dispencer side (door and Pin) You have to assemble to reinstall (not easy to install while assembled) Install the pivot pin the rest of the way with the new spring mounted and when unit is almost in place, install the pivot the rest of the way, install tension hold downs that old both the water and ice dispenser shafts, reinstall cover, reconnect wiring and test, I had to remove the plunger because the water wouldn't shut off fast enough. Unit works great now.

Frezzer was not defrosting ans the refregitor was not cooling.

  • Customer: Errol from Brooklyn, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My Whirlpool refrigerator frezzer was not defrosting and the refrigator was not cooling. I followed the symptom parts advise (Defrost Timer Kit and the Bimetl-Def)of P/S. I pulled out the refrigerator from it inclosure and unpluged it, (note the shelf supports, the thinner ones are on the left side) I remove the shelfs and their supports,I removed the interior back cover of the frezzer, using a hair dryer I melted the frozen ice from the frezzer coile. Once all the ice was melted away, I cut off the old BIMETL-DEF and attacth the new BIMETL-DEF making sure the color wires are match correctly and using electrical connection plugs and electric tape I reconnected the wires. (2) I followed the video instruction for replacing the Defrost Timer Kit I found it to be quite easy to follow. The most deficult part was trying to position my body to remove the screws. I used an old CREDIT CARD to remove the face of the Refrigerator control buttons in order to access the compartment which house the Defrost Timer kit. I removed the old Defrost time kit and replaced it with the new one (following the Video instruction). I replace the frezzer cover inserting the lower four screws then using an old Credit Card I forced the top end of the frezzer cover under its retaing wall. I then replace the remaining two screws. JOB DONE
All Instructions for the ASD2522VRW00
571-585 of 952