ASD2522VRW00 Amana Refrigerator - Instructions

I was at a loss. Did not know where to find the part. Opened the website and navigated for a minute, then put in part number of the broken piece and the right part popped up! I ordered two and they came to my door in two days, popped into place and fit perfectly! Problem solved, no stress.....what a treat.

got the ice marker in record time, then need to replace old wiring from the new one, the new one did not reach.used a nut driver put it in and cubes golore.thanks parts select great job.

Took the bolts at the bottom of the door off and removed the door. Pried out the old cam and put the new one in. Put the door back on and it works like it is brand new. The fridge is 13+ years old

Followed the video on Parts Select and it was a breeze.

It took longer to get the part than it took to repair the water inlet. The help from the staff was very responsible and the repair direction off of the net very clear and understandable. I order the wrong part and was offered assistance and directed to the correct part than there were no issues but clear sailing.

Removed to old motor by removing screws and disconnecting power source and replaced with the new motor and plugged back in power source

Using a 1/4" ratchet removed the old motor, a bit difficult due to small space to get your hand and ratchet in position. Before installing the new motor I used one of the screws to tap the the 3 holes in the new motor so it would be easier to start the screws attaching motor to mounting bracket. Attached cable. plugged in the fridge. Great to hear a quit running refrigerator again.

Watch the Video! My reefer's ice door/spring 'pin' removal and installation is different than what is shown in the video. That is, my spring 'pin' looks more like a long nail (with a head on the right end). After inserting the left end of the pin into the hole, the head end drops down into a notch, which makes removal and installation easier than what is shown in the video. It is much easier to reinstall everything if the 'ice-chute' is installed first. Then, maneuver the ice door assembly into place and install the pin. I used Blue masking tape to hold the control panel up and out of the way. This is the second ice-door repair since I've had this refrigerator. It seems to occur with 'heavy' use of "crushed" ice. Some crushed ice backs up behind the ice door/flap, jams/holds the flap open, letting warm air into the freezer, causing the crushed ice to freeze into a big 'clump' of ice (too big to come out of the chute, and causes frost in the freezer. If you get a clog like this, I suggest removing the ice "bin" and gently clearing the clog from the top side of the ice chute with tongs or needle nose pliers. If you try to remove the clog from the bottom of the ice chute, the door becomes dislodged or breaks...

Thermostat replacement

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

The customer service people did some cross checking and found a shelf and drawer that would work in my fridge. It did!! I love it now!!!Thanks for your help I did have to remove one of the selves - but now I have an extra!

I followed the video and was done with the replacement in less than 20 minutes. Just make sure after turning the water back on you check for leaks before you move the refrigerator back.

Remover bottom nut screw and loosen the top two nut screws about half way out. Lifted up and foreward and then tilt ice maker to the right pushed in tab on electric plug and pulled plug out. Removed ice shut off rod and installed it on new ice maker. Removed nut screw on chute and removed chute. Installed new chute, plugged ice maker in and re- installed ice maker. Very easy and pleased with how quick I received the part after I ordered it.

Watched the video provided, then followed that procedure. Everything now works fine, no more clicking.

Before I began I unplugged the electrical at the wall outlet. 1. Unscrewed the 4 mounting screws. 2. disconnected electrical at the motor. 3. removed the assembly. 4. mounted the new motor on the assembly as described in the instructions. Installed the assembly and reconnected the electrical. Works great, easy job!