Models > ASD2522VRB00 > Instructions

ASD2522VRB00 Amana Refrigerator - Instructions

All installation instructions for ASD2522VRB00 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ASD2522VRB00
751-765 of 925
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

refrigerator would not run

  • Customer: william from charlotte NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
The Sears man came out and told me it was the thermostat that needed to be replaced and it would cost $321 plus tax. I went on youtube and watched the Partselect video several times and decided to order the part after seeing how easy it was to install. Total cost $65. I put the laptop on the counter and watched it as I installed it. It helped that I could go back and watch a certain part if there was a problem. But I had no problems and installed it in 20 minutes. Very, very simple to do. Of course I had to pay $75 to the Sears man but I saved about $200 . Thanks Partselect.

Refrigerator freezing regardless of settings.

  • Customer: James from Taylorsville NC
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
When my thermostat was shipped the email contained a step by step video. I just watched the video and installed it.

Refrigerator would stop running but when touched it would run again

  • Customer: Wilton from Huntley IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
1. Unplug the electric plug. 2 Either be in a well lighted place or get a flashlite. 3. Remove all food from top shelf. 4. Remove the knobs from both controls by pulling on them or use pliers to grab the center and pull. 5. Use the thin bladed knife and gently slip the knife under the thin plastic panel that covers the two controls and pop it off. 6.Go in back of the control panel and remove the two hex headed screws that holds the panel onto the roof of the refrigerator.7. Locate the right hand control, and use a philips screw driver to remove two philips screws that hold the temperature control body in place. and remove the wires from the terminals by pulling them with a long nose pliers.8. Locate the white panels that cover the thermostat sensor and remove the screws holding them onto the frig body. slip the long thin tube out of the plastic piece it is formed to fit.9.Draw on paper the shape and measure the deminsions,of the long thin tube. Straighten out the tube and remove the plastic covering it. Now slip that tubing over the new piece.10. Form the tubing into the odd shaped holder and gently place all of the new asssembly against the frig wall and cover with the two white panels that you removed to get to the long sensor tube. 11. Reassemble the controls in the same order you took it apart. Plug the frig back in to the electricity and set the control on 5 and it should run. Watch for a period to hear the unit cycle on and off. You are a genius and have saved at least 150 dollars.

Refrigerator/freezer geting warm

  • Customer: Crystal from Buckhannon WV
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We suspected the thermostat assembly was the problem. We reviewed the video provided by PartSelect and accessed the thermostat assembly. To ensure the thermostat assembly was likely the culprit, we used a multimeter to test it. We ordered the assembly from PartSelect and were pleasantly surprised at the speedy delivery. Using the same video, we replaced the assembly and put the refrigerator back together. Thank you so much for saving us money we didn't have for the repairman. We will be ordering again soon to repair a leaky waterline and ice maker.

Old thermostat was shot.

  • Customer: Thomas from Stone Creek OH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Just like the video I watched online at your web site. piece of cake.!!

Refrigerator not cooling, compressor not kicking in when thermostat switch turned on and off.

  • Customer: Keith from Fort Smith AR
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Very simple repair. Followed the video instructions. Simply removed a few screws and nuthead screws. Removed the cover plates. Removed the old thermostat switch. Removed the plastics tubing over the temp sensor probe. Put the plastic tubing on the new sensor probe, ( rubbing a slight amount of vegetable oil on the probe to allow the tube to slide on easier,). Reinstalled the temp probe. Reinstalled the new switch. Connected the wires to the switch. Reinstalled the cover plates and screws. And the job was complete. Almost took me longer to write this out, than it did to complete the project. Hey, it was an easy fix.

Fridge was too cold, freezing food!

  • Customer: Edward from Spring TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed the cover from Thermostate, removed the wires, and screws holding old thermostate, reversed instulation with the new thermostat, pretty simple.

Thermostat problem

  • Customer: Juan from Sugar Hill GA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Thermostat replacement

clip for holding tube

  • Customer: John from Sanford ME
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
repair went good .only had problem removing tube from clip in front

Refrigerator would not run

  • Customer: Rodney from Rockdale TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your installation how to video. Applied same procedure. Went smoothly.

Fridge stops cooling

  • Customer: Daniel from Austin TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Fridge would stop cooling, get way over temperature. I noticed it would start up again if I tapped near the thermostat. It would run for a while then stop again. Replaced the thermostat exactly as shown in video. Fridge works fine now.

refig kept defrosting

  • Customer: andrew p from white plains AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
all is fine now. thanks andy

refrigerator not cooling but freezer worked well

  • Customer: Vernon from Moorehead KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
watched the video followed the instructions and the repair took less than 30 mins. thank you parts plus for the video ref now workes properly and saved me a bundle of money

water stained drip tray

  • Customer: Laura from Knoxville TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
pop in and presto! simple, no tools required, perfect fit.

Broken roller wheels

  • Customer: Joseph from Tyrone PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Followed the instructions on package, went extremely well, with no problems what so ever! Thanks so much for the part and how to do list!
All Instructions for the ASD2522VRB00
751-765 of 925