Models > ASD2514ARA > Instructions

ASD2514ARA Admiral Refrigerator - Instructions

All installation instructions for ASD2514ARA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ASD2514ARA
76-90 of 675
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Door parts separated, didn't seal or function

  • Customer: Derek from Leslie MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 4 of 4 people found this instruction helpful
Followed the directions included with the parts, which were exact and well illustrated. If you are comfortable working around circuit boards and electrical connectors (with the power OFF, please!), then you can do this repair. Why electronics on this repair? Because you have to unplug a board to get to the parts, and disconnect the connectors to the solenoid. But again, the directions were fabulous, and I'm almost looking forward to needing to use PartSelect again. Almost.

Ice maker eitehr wouldn't make ice, or made odd shaped cubes

  • Customer: J. Bradley from Wellsville NY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

condenser fan stopped working

  • Customer: Steven from Brigham City UT
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
1. Removed the cardboard cover.
2. Removed the terminal block and unplugged the old motor.
3. Removed three screws that held old motor to the bracket.
4. Removed the fan blade from the old motor.
5. Installed the fan blade (after cleaning) to the new motor.
6. Crimped on new wire terminals onto the leads on the new motor.
7. Installed the new motor using the fasteners provided.
8. Plugged the new motor wires onto the proper terminals in the terminal block.
9. remounted the terminal block.
10. reinstalled the cardboard cover.

Ice maker just stopped making ice

  • Customer: Thomas from Valencia PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 4 of 4 people found this instruction helpful
This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

The round door on my ice chute broke off

  • Customer: Stanley from Avon IN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 4 people found this instruction helpful
I ordered the ice dispenser and selenoid door kit, it was easy to repair because I only needed the door. As per the instructions I removed about seven screws and disconnected the power source to the dispenser unit, pulled the unit out
and replaced the door in the two slots. Plugged the power source back into the slot, put the screws back in, now it works like new.
Thank you PartSelect, I received the part in just a couple of days. I recommend your service to everyone. I saved myself a lot of money and will order again on any needed
parts in the future.

The plastic ring that is the connection between the drive motor at the back of the freezer compartment to the auger in the ice bin shattered when my wife was dispensing crushed ice.

  • Customer: Larry from Anchorage AK
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Part selects cataglog for parts selection was very easy to use and the online service and delivery was great.
When I got the part, it was not apparent on how to remove the auger so that I could insert the new connector. There were about about 8 visible screws, with star drive heads that I fortunately had a screwdriver that fit, and I could not tell if I had to remove all of them or only a couple.
I ended up removing all, but still could not separate the dispenser portion which held the front of the auger from the back of the ice bin. I finally figured out that the dispenser door trip lever had to be disconnected and I almost lost it when I removed the metal clip that attached it to the outside of the ice bin when the spring loaded lever tried to unwind. I managed to hold it in place, separate the dispenser holding the auger from the rest of the ice bin and replace the connector. I them got the pieces back in place and was able to refasten the spring loaded lever and then replace the screws.
If the spring loaded lever had unloaded, it would have been tricky to try to replicate the amount of turns (load) on the spring tension.

Ice wouldn't eject from ice dispenser

  • Customer: Gayle from Fair Lawn NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 4 of 5 people found this instruction helpful
I removed the black drip grill and unscrewed the two screws holding the faceplate in place. After unplugging the faceplate from the dispensing unit, I removed the four remaining screws; be careful, one screw is shorter than the others.

I then pulled the dispensing unit away from the freezer door and removed the ice door assembly. WARNING: Make sure that you look carefully at the alignment of the return spring BEFORE you even touch it because as soon as I started using the needle-nose pliers to remove the spring, it shot across the room! Also, look carefully at how the end of the plastic rod fits over the old solenoid; in fact, look carefully at the entire plastic rod and how it aligns with everything!

Unfortunately, the pictures in the instructions are fuzzy so you can't really see how the spring is installed and how the plastic rod fits over the solenoid.

The solenoid was easy to remove and replace. Be aware that the plunger part of the solenoid slides in and out easily, so it's easy for it to fall out of the solenoid unit and roll away.

Once I had everything back where it was supposed to be, I screwed everything back in and the ice/water dispenser worked like new. I was even able to clean off some calcium deposits inside the unit while I had it opened.

If I have to do this again, I would estimate that it would only take 15-minutes or so. It took me longer because I didn't look at the alignment of the plastic rod in relation to all of the parts---that is one of the most important steps of this operation.

Anyone who is comfortable using tools and working with small parts should be able to complete this replacement project with minimal difficulty.

Icemaker would not fill with water.

  • Customer: Linford from Cedarville NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 8 people found this instruction helpful
Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

Refrigerator quit cooling and the freezer wasn't freezing anything

  • Customer: Tonya from Grand Prairie TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 4 of 5 people found this instruction helpful
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

My old icemaker lost some of the nonstick surface and the ice didn't want to come out

  • Customer: Thomas from Ruth MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Ice shoot door broke and would not open or close

  • Customer: Michael from Arlington VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
Removed the drip tray and cover panel. Then removed shoot housing, replaced broken door and reassembled in reverse order. Easy as pie.

Ice cubes would not stop discharging

  • Customer: solomon from henrico NC
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 3 people found this instruction helpful
After going to manufacturer's web site and customer service phone, was unable to locate the correct switch in the dispenser area on the door. Your web site had the picture of the switch and it was right on and in stock. Shipping was quick and inexpensive. Repair went quick and all is well.

automatic ice door would not open

  • Customer: Gerald from colonia NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 3 of 3 people found this instruction helpful
removed the front panel on freezer door ,removed and disconnected panel ,removed panel containing solenoid,replaced with new solenoid. replaced all parts. works perfect..

Broken ice enclosure

  • Customer: Robert from Hinesville GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 5 of 9 people found this instruction helpful
The ice enclosure was broken where the element is attached to the enclosure. There was some ice buildup in the ice bin and looks as if the auger got bound up and twisted the element attachment until it broke the housing of the enclosure. We got on line and fround the part at PartSelect. The selection process was very easy since PartSelect had all the parts pictured and described. We ordered the part first thing on a Monday morning and received the part Tuesday morning. We are very inpressed with the company and the fast service in receiving the part. Thank you. If the need arises we will order from you again and recommend you to friends.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 6 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
All Instructions for the ASD2514ARA
76-90 of 675