Models
>
AS2728GIHB
AS2728GIHB Maytag Refrigerator - Overview
Sections of the AS2728GIHB
[Viewing 13 of 13]
.gif "SUPPLEMENTAL INFORMATION Diagram and Parts List for Maytag Refrigerator")
Manuals & Care Guides for AS2728GIHB
Click to downloadKeep searches simple, eg. "belt" or "pump".
Water Filter
PartSelect #: PS11722137
Manufacturer #: EDR7D1
This is the replacement water filter for your refrigerator. It is white in color with a red cap and is approximately 3 inches wide and 6 inches tall. The water filter reduces contaminants and improves...
No Longer Available
Door Switch
PartSelect #: PS12731166
Manufacturer #: W11396033
This light switch may also be known as a refrigerator door switch or a light switch kit, and is compatible with your refrigerator. The function of the refrigerator door switch is to turn on the light ...
$27.65
In Stock
Crisper Drawer Shelf Support
PartSelect #: PS2071530
Manufacturer #: 67764-1
This crisper drawer shelf support is used for many refrigerators.
No Longer Available
Ice Door Assembly
PartSelect #: PS11743244
Manufacturer #: WP61005883
This ice door assembly is a little over three inches in diameter. It is all white in color and it is made entirely of plastic.
$17.69
In Stock
Screw
PartSelect #: PS12349731
Manufacturer #: W11233072
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
$20.79
In Stock
Lower Hinge Pin
PartSelect #: PS2058840
Manufacturer #: 61003174
This lower hinge pin is almost two inches long. It is made entirely of plastic and it is all black in color.
No Longer Available
Water Fill Cup and Bearing
PartSelect #: PS11743318
Manufacturer #: WP628356
This refrigerator ice maker fill cup dispenses the water into the ice cube mold during the fill cycle. Replacing the water fill cup is a possible solution if you notice that the ice maker is leaking, ...
$40.40
In Stock
Limit Switch - 2 Terminal
PartSelect #: PS2060868
Manufacturer #: 61005520
This limit switch is located in the ice/water dispenser section. The switch pictured here is black, though this type of switch is also available in white.
No Longer Available
Door Shelf Bucket Stop
PartSelect #: PS2058491
Manufacturer #: 61002719
Sold individually.
$18.13
In Stock
Rack Roller
PartSelect #: PS11743137
Manufacturer #: WP61002307
This rack roller is well under an inch in diameter. It is all white in color and it is made entirely of plastic.
$10.79
In Stock
Ice Chute Door Return Spring
PartSelect #: PS2059882
Manufacturer #: 61004388
Sold Individually.
$11.10
In Stock
Questions And Answers for AS2728GIHB
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the AS2728GIHB
[Viewing 13 of 13]Light not working
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Ice maker not making ice
Fixed by
these parts
these parts
Show All
Not dispensing water
Fixed by
these parts
these parts
Show All
Ice maker won’t dispense ice
Fixed by
these parts
these parts
Show All
Door won’t open or close
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Ice maker dispenses too much ice
Fixed by
these parts
these parts
Show All
Fridge too warm
Fixed by
these parts
these parts
Show All
Door Sweating
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Fridge too cold
Fixed by
these parts
these parts
Show All
Freezer section too warm
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
The Bearing Cup Assembly was broken and ice would jamb against it during the ice making cycle.
I removed the ice maker from the refrigerator, by removing one screw on the underside bracket and loosening the two screws at the top side, then lifting the ice maker off the loosened screws. I then unplugged the electrical harness that supplies power from the refrigerator to the ice maker. I then disassembled the ice maker by removing
... Read more
the front cover which is snapped in place, then removing two recessed screws at the front. I removed the broken part, I then reassembled the ice maker with the new part. I replaced the two recessed screws at the front and snapped on the cover. Then I reinstalled the ice maker in the refrigator by plugging in the harness, slipping the ice maker over the loosened screws in the refrigerator and replacing the screw that was removed from the underside bracket. Tightening all the screws completed the project.
Read less
Parts Used:
-
David from Chester, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
107 of 133 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Filter needed replacing
Turn counter clockwise, following the remove arrow on the filter, until it stops. Wiggle and pull down on the filter until it comes off. Put date sticker on new filter to remember when it was replaced. Align the lines on the filter and push it up where the old one was and turn it clockwise until it stops, following the install arrow.
... Read more
Close the door and push both the light and lock button together to reset the replace filter light. Run the water through the door for a couple minutes to get all of the air out of the system. Very easy and quick. Most time spent flushing out the air.
Read less
Parts Used:
-
Bruce from Alfred Station, NY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
92 of 104 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice dispenser cover flap was broken.
First I unpluged the refrigerator, then I removed the drip shelf (slides out). Then removed the two screws hidden by the drip shelf. Then I removed the control panel by pulling out on the bottom then lifting slightly to to expose the ribbon cable. The circuit boards you see at this point will deliver an electrical shock if the refrigera
... Read more
tor is plugged in. I disconnected the ribbon cable form the control (front) panel. Next I removed three screws that hold the chute assembly in place and worked the chute away from the door. Pay attention to the placement of the water line before you remove the chute. The bad flap fell out at this point but it is easy to fiqure out how to place the new one. When putting the chute back in place make sure the arm holding the flap is aligned in the groove of the solenoid plunger and not just setting on top. (I had to do this twice because the chute would not open the first time I put it back together). About a 30 min job because I took it apart the first time to see what was broken. I only needed the flap, the arm it mounts to an the solenoid were not broken. Easy to do and only cost about $16.00 with shipping for the part.
Read less
Parts Used:
-
Philip from Plantation, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
78 of 80 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!