Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ARSE66ZBW (PARSE66ZBW0) > Instructions

ARSE66ZBW (PARSE66ZBW0) Amana Refrigerator - Instructions

All installation instructions for ARSE66ZBW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARSE66ZBW
46-60 of 671
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker wouldn't work

  • Customer: Ty from Shepherdsville, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 13 of 18 people found this instruction helpful
First I removed the outer shell part then removed the 4 screws holding the ice bin together.After taking the parts out of the old ice bin it was easy to put all the new parts together except the new helix end cap which was a bit tricky to put it in place.It wasn't difficult to reassemble but I would stongly suggest taking notice how everything fits together before taking it apart.

Refrigerator Ice Maker stopped making ice.

  • Customer: Harold from Oakton, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 13 of 19 people found this instruction helpful
(1) Removed the three screws which attached the ice maker to the freezing compartmnet wall in refrigerator; (2) Disconnected the power to the old ice maker; (3) Removed the old ice maker from the freezing compartment of the refrigerator; (4) Took the white front cover off of the old ice maker; (5) Disconnected the wiring harness from the old ice maker; (6) Removed the "ice making-stop arm" from the old ice maker; (7) Placed the items taken from old ice maker on to the new ice maker; (8) Reconnected the new ice maker to the power; (9) Placed the new ice maker in the proper position in freezing compartment of refrigerator and replaced the three screws. JOB DONE!

ice wheel was broken

  • Customer: rosemarie from duarte, CA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers
  • 10 of 12 people found this instruction helpful
remove the bin from the freezer, there are 2 tabs on the lower front cover that pop off and you just pull the entire front cover off. there are 4 nuts that hold the blade cover which you can use the 7in1 with the insert removed.. i believe it's 5/16". remove the cover and the tumbler assembly pops out of the tray.
remove the nut with a set of pliers and lay it out on the table in order.
install is reverse of removal. make sure you get all the washers in the correct location when assembling. don't tighten the nut too tight or it will bind the rotating assembly.

enjoy retrieving ice from the door again!

fridge side was not getting cold

  • Customer: neil from murfreesboro, TN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 12 of 18 people found this instruction helpful
first I removed the panels to see if the coils were getting frosty . Then I noticed that the fan was not spinning. I tested voltage to the fan and it was hot. I ordered the new fan put it in placve and, voila!.
Fixed my fride for under 50 bucks

ice bucket had a hole in it.

  • Customer: John C. from Erlanger, KY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 9 of 9 people found this instruction helpful
removed old ice bucket by lifting up on the front and pulling straight out.Remove the front it just snaps into place.Remove the cutter comes out real easy.Put these parts on the new bucket.Slide the new bucket back in your done.

Drain pan failed and had many leaks

  • Customer: Malcolm from Parrish, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 15 of 27 people found this instruction helpful
Took two times getting the correct part, however after getting the correct part it took about 10-minutes to replace. Had to take the fan out. When you put the new drip pan in make sure it is positioned so that the guides on the pan aligns with slots in the bottom refrig brace, otherwise back pannel will not align correctly. The fan is very easy getting aligned in the new tray. May take a little effort. I do not know why the pan on a refrighterator that is less than 5-years old could start breaking into many pieces.

Fridge stopped working

  • Customer: Dan from Sumner, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 9 of 10 people found this instruction helpful
I called a repair man from a pretty large name to come out and take a look. He found out in about 10 minutes that it was a bad capacitor. The quote he gave me was $75 for the part and $175 labor. I tried my best not to laugh and tell him no thank you. He did have to charge me for him to show up, which was only $98.
So I used what he told(minus the "scrap it") and opened it back up. Although he had left wires everywhere and the broken pieces laying inside, I thought it was enough for me to order the part. PartSelect was very easy to navigate and ordering was a breeze. Took about 4 days to get the part and I ordered in the X-mas craze. Fixed it in about 15 minutes.

Left front plastic wheel was broken

  • Customer: mike from holly springs, NC
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 10 of 13 people found this instruction helpful
Pop loose the plastic grate at the bottom.

Locate and remove the wheel leveling screw from the front bottom corner.

Remove cotter pin from the pin that mounts the wheel assembly to the refrigerator. Tap out the mounting pin.

Lift out the wheel assembly.

Remove the Roller pin from the wheel assembly. I used a Dremel tool with a cutting disk. A hack saw will also probably work.

Install the new roller pin and wheel into the wheel assembly. Use a hammer or vice to peen over the end of the roller pin.

Reinstall and adjust wheel assembly.

Ice maker leaked water

  • Customer: Robert from Pennsylvania Furnace, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 10 of 14 people found this instruction helpful
Overall, replacing the ice maker wasn't too bad but it wasn't nearly as easy for me as it seems to have been for some. In my case, the fridge was an Amana and the ice maker was mounted in such a way that disconnecting the power connector was difficult. The ice maker had to be completely dismounted before any access to the power connector was even possible. The short power cables made it very difficult to get the ice maker into a position where I had a good view of the power connector enabling me to see how to release it. The only other challenge was the cup that the water line goes into. The replacement ice maker did not come with the right cup - the instructions said to replace the provided one with the old one. No instructions for this procedure were provided and it looked to me like it might involve significant disassembly, something I wanted to avoid for fear of breaking a plastic part on the new ice maker (something I had already done when disassembling the old ice maker). So instead of replacing the cup, I modified the new one to match the old one. This involved removing a cutout on one side and covering a hole on the other. Installation of the new ice maker went fine and the water leak problem was fixed.

Large Crisper Drawer Cracked And Broke So I Could No Longer Push The Crisper Drawer In And Out

  • Customer: Jeffrey from Elburn, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 8 people found this instruction helpful
I removed the old crisper drawer, took all the fruits and veggies and put them into the new crisper drawer, and then slid the new crisper into position. If was the exact size and part I needed.

Lower RH door hinge was making a snapping noise because door closure cam screw backed out and damaged cam by egg-shaping hole.

  • Customer: Keith from Glenview, IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 8 of 9 people found this instruction helpful
Removed door. Removed old cam closure assembly. Noticed that there was almost nothing inside the door for screw to screw into(only styrofoam insulation), which is why original screw backed out. Bad design. Got longer screw at bigger diameter. Pushed high strength glue into hole, on screw threads, and underneath screw head. Assembled. Crossed fingers. About three weeks have passed and so far, so good.

Six months in use time to replace the filter

  • Customer: Michael from Long Valley, NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 16 people found this instruction helpful
It is simple, unscrew the old screw in the new one.

Replace water filter

  • Customer: Brenda from Spokane Valley, WA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 17 people found this instruction helpful
pop open, unscrew quarter turn, screw new one in quarter turn, pop shut. duh

Needed to replace a broken light switch

  • Customer: Ethan from Fort Collins, CO
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 11 people found this instruction helpful
Popping out the broken switch was easy once I was able to see how the new switch part was engineered. The switch was made to be replaced, having a simple tension hook on the bottom of the switch which needed to be depressed to pull the switch out of the cabinet. Once pulled out, there were modular plugs for the power line that were easy to pull off the broken switch and plug into the new switch. Pop the new switch back in and VOILA, the lights worked again! Thanks to part select's good diagrams of the actual model of my refrigerator, it was very easy to hone in on the exact part I needed. I did notice one problem with the order as the correct series for the part was displayed earlier in the process, but had the wrong series later in the process. However,. I trusted the system and the part is for the right series and fit well (an exact match, down to the color). Thanks Part Select, I would definitely use you again.

Broken cup water fill on ice maker

  • Customer: Matthew from Aurora, CO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 7 of 8 people found this instruction helpful
I called the local Amana repair man, wanted $150 for a new ice maker because they could not get the part I needed. Found Partsselect.com and the part cost $17 with shipping. They saved me over $100. The repair was very easy too, just removed a couple of screws.

Thanks,
Matt
All Instructions for the ARSE66ZBW
46-60 of 671