Models > ARG7600WW (P1141298NWW) > Instructions

ARG7600WW (P1141298NWW) Amana Range - Instructions

All installation instructions for ARG7600WW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARG7600WW
1-15 of 210
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't heat. Glow ignitor was weak and wouldn't ignite flame.

  • Customer: John from Niles MI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 34 of 34 people found this instruction helpful
After shutting off the gas and removing the oven door, which simply slid off of the hinges, I removed the oven plate. The ignitor was attached to the manifold. I removed that and noted the wires were attached back behind a hole in the back of the oven. I thought I would have to access them from the back but when I pulled on them I was able to reach them from the front. I was surprised to find plastic lugs covering the wire ends, rather than ceramic. I attached the new ignitor wires and reused the plastic lugs, as no ceramic ones came with the new ignitor. I carefully slid the new ignitor back into the cage/shield attached to the manifold and replaced the manifold. I then turned the gas back on and tested the ignitor (which worked perfectly) before replacing the oven plate. The repair took less than 30 minutes, but my wife and I thoroughly cleaned the door and interior while we had it apart. The hardest part was getting the door back on the hinges, but this too was accomplished after several attempts. The oven heats up beautifully now.

Oven not working but broiler was working fine.

  • Customer: mark from macomb MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 37 of 45 people found this instruction helpful
Checked lower oven burner for a problem. Oven Ignitor looked like it was glowing and working properly but the gas valve would not open to let the gas flow to burner. I had read on a forum that just because the oven ignitor looks good does not mean it is creating the proper resistance to open the gas valve. So I took my chances and replaced the ignitor (because it was cheaper than the gas valve) and now the oven works like new.

Broken Electrode, no spark

  • Customer: HUY from ALISO VIEJO CA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 29 of 36 people found this instruction helpful
Remove 2 screws holding the top burner. Remove 1 screw holding the electrode. Remove electrode from wiring using plier. Install new electrode and top burner

Getting F 1 and 2 error codes and the oven turned itself off.

  • Customer: Suzanne from Acton MA
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 39 of 76 people found this instruction helpful
Really easy but in this model there are 2 versions of the sensor, male and female. The website didn't have any place to see that. So the first sensor that came was male but we needed the other. After calling they sent me a return form and sent the new part (which was actually much cheaper) overnight and it went in very quickly. Would check this out again when anything went wrong. they are great folks to work with.

Igniter glows, oven won't light

  • Customer: David from Avon IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 15 of 16 people found this instruction helpful
I removed the cover over the flame diffuser, then removed the single nut holding the diffuser to the burner assembly. After removing the three screws from the igniter assembly I found I couldn't reach the connector for the igniter.
I removed the storage tray underneath and found a cover towards the rear of the oven with two screws. After removing this piece I could easily disconnect the igniter. It was a bit difficult replacing this shield as it had to fit between two other pieces on the side towards the front of the oven.
I slid the guard from the old igniter and put it on the new piece and just reversed the procedure. Relatively easy and saved me a bundle!

2 of 4 burners wouldn't light

  • Customer: John from Alexandria VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 15 of 17 people found this instruction helpful
Unplugged the stove, removed all 4 burner discs from the stove top (2 screws each) and disconnecting electrode wires as I pulled them out, removed the stove top, unscrewed the old module, removed the 6 wires, connected wires to the new module, screwed it into place, reinstalled the top while poking the electrode wires through the top one by one, put the stove top in place, connected the wires to the burner discs. Done, and it works! It took longer to find and order the part than it did to change it out.

Oven would take awhile to light causing gas fumes

  • Customer: james from Waukesha WI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 13 of 17 people found this instruction helpful
I opened the oven and cleared the racks;
removed the cover of the oven heating area;
took off the nut holding the blast shield on;
removed all the screws holding the drip tray on;
some were quite rusty and fell out in my hand;
removed the 2 screws holding the igniter in;
and the one scew that allows adjustment;
pulled out the igniter and noticed the old one was connected with wire nuts while the new one had a module plug;
cut off the module plug and stripped back the wires;
applied the wire nuts;
stuck the wires back in tjhe hole and screwed it all back together-done,
I must say the best part of the repair was googling the problem "amana oven ignition troubleshooting" and getting a helpful discussion of the problem and a solution and a link to the parts suply house, It couldn't have been simpler. I got the part 2 days after ordering it online.

Burner would not ignite when control in "light" position

  • Customer: Michael from Friendswood TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Remove the two screws from the burner assembly (on top of the burner). Lift burner assembly from the cook top. Disconnect the electrode wire from the electrode. Remove the screw holding the electrode to the burner assembly (on bottom of burner). Install the new electrode and attach the electrode to the burner assembly. Attach the electrode wire to the electrode. drop the burner assembly back into position on the cooktop. Attach the burner assembly using two screws.

The Amana oven & broiler igniters failed after 7+ years of service

  • Customer: Mark from Munroe Falls OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 10 of 10 people found this instruction helpful
Broiler Igniter:

Disconnected stove from electricity

Removed the two screws that hold the broiler igniter assembly

Pulled asembly out to expose ceramic wire nuts

Removed ceramic wire nuts and save them

Removed broiler igniter assembly (broiler igniter & brolier mounting bracket are assembled together)

Loosened screws/nuts that hold the broiler igniter to the brolier mounting bracket

Remove old broiler igniter

Carefully inserted new brolier igniter into the broiler igniter bracket

Place the brolier igniter bracket into position. Make sure you look at the diagram provided so the position is correct. There is a "up" & "down" side to the broiler igniter

Tightened screws & bolts on broiler igniter bracket

Reconnected the ceramic wire nuts

Inserted two mounting screws and tightened

Finished.

Oven Igniter:

Removed oven door

Removed bottom oven drawer

Removed nut that holds heat shield/disperser in place

Removedheat shield/disperser

Removed all oven tray screws

removed oven burner

disconnected oven igniter

disconneted oven igniter assembly

inserted new oven igniter

reassembled

Spark did not ignite one burner and sometimes two

  • Customer: Frederick from Eagle WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 10 of 12 people found this instruction helpful
I could not figure out how to get to the igniter until I went to the "Part Select" web site and found a post that was exactly like the problem that I had. IE: Remove two screws holding each burner, Lift off top, remove old igniter being "Carefull" not to mix up the wires when putting them on the new one, installed new igniter in bracket and mounted in position, Reinstalled top and PRESTO - it worked. First post was VERY HELPFUL. Thank you

Oven wouldn't ignite

  • Customer: Keith from Denver CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 9 of 9 people found this instruction helpful
Bought new igniter based on advice from other stories here. Didn't test the impedance. The igniter glowed, but the oven wouldn't start.

1. Removed single nut on flame pan & remove pan.
2. Removed Pan drawer and disconnected plug to igniter.
3. Removed 3 screws holding igniter in place.

Note: the screws were corroded & one stripped in removal - you may want to purchase the metal housing for the igniter assuming it comes with new screws.

4. Put everthing back in opposite order.

Two of the four burners would not ignite when lighting the stove.

  • Customer: Dave from Livonia MI
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
I thought the problem was with the ignitors/burners since they appeared to be worn. As it turned out, I needed the spark ignitor, which is a "brain box" located under the range cover. It connects all of the ignitor/burners and sends current to the ignitors to give it the "spark" to ignite the gas. It was really easy to replace.

The burner bowls were damaged due to wear.

  • Customer: Margaret from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
No tools were needed; the old burner bowls were taken out and replaced with the new burner bowls. I would like to say the service was great from PartSelect. com. I was so happy I was able to find replacement bowls for my older drop-in range that I ordered a second set to keep for future use. PartSelect.com sent the replacement bowls quickly, and the order was processed very efficiently. Thank you!

Oven ignitor stopped working (does this every 6-7 years)

  • Customer: Jean from Manalapan NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 8 of 9 people found this instruction helpful
First we removed the oven doors. Then removed the shelf that separates the oven from the broiler, giving us more room to work. At first we thought we needed to loosen the screws around the bracket holding the ignitor, but we realized that the burner needed to be removed. Lifting the burner up from the front gave us the room to pull it gently from the back of the oven wall, giving more room to pull the wires connected to the ignitor from the back of the oven wall out and then disconnecting them. Then carefully pulling the ignitor out of the bracket.

Putting the new ignitor in was easy. Carefully sliding it into the bracket, not touching the ceramic piece, connected the electric wires, pushed the wires back into the hole in the back of the oven. Then placing the burner back into place.

We then turned on the gas and the electricity and the ignitor glowed and the burner lit. PERFECT! In the past we've had a repair man come in and this time we saved $100. Even more perfect.

Cracked inside glass window of oven door

  • Customer: Uday from Ann Arbor MI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 7 of 7 people found this instruction helpful
1. Slide the Oven door out of its hinges after removing the screws - see Owner's manual.
2. Place door on floor with the inside face on the floor.
3. Remove screws on side and bottom of door and the lift away the side stamped pieces.
4. Remove screws as they becom visible and lift away the pieces till you reach the inside glass.

Remember the sequence and be careful not to strip the Phillips screws when unscrewing.
All Instructions for the ARG7600WW
1-15 of 210