ARG7301WW (P1143315NWW) Amana Range - Instructions

Removed old assembly, attached wires to new and inserted into space for same. Of course you must turn off the range circuit breaker. The part that took the most time was removing the old assembly. Once that was done, the rest took only a few minutes.

Removed oven door. Removed three screws on ignitor holding bracket. Pulled out the range from the wall and reached underneath to access the wire nuts on the wires. Removed old ignitor and replaced with new one. Reconnected wires and then and replaced bracket and that's it. Works great now.

I removed all 4 burners 2 screws holding each,replaced the ignition module,wire for wire,reassembled after cleaning the stovetop.I,m my wife's hero.

Philips is all that's needed. Remove the burners (2 screws each) lift off top of stove, replace the ignition module. put all back together and your done. Local parts store wanted $80+ for the module. PartSelect only $50 total cost and it hit my mailbox in TWO days! Thank you PartSelect.

I just ordered a new wire oven rack from you. When it came all I had to do was to remove it from the carton it came in and place it in the oven. It fit perfectly. Thanks

Removed two screws per burner. Unhook wires. Putting back broke slide on connector and had to replace. That took longer than the whole job. I ordered the part before 3:00 pm and it was at my house tjhe next morning which was hard to believe. The instructions that come with part made no sense what so ever. Thanks for the quick service and I will be back.
Dave

Un plug elect. Cord. Remove door by pulling upward removed back stove panel, un did 2 wire nuts leading to igniter. Un screw igniter inside oven at top next to burner pad. Interchanged old ignitor with new plug stove back in. Thats it.

The earlier reviews said very easy and 15 minutes for beginners. They were right on, except I could not get the old screw out no matter what I tried. I eventually had to drill it out and put in a self tapping new screw. This was a first for me. Then it took 15 minutes or less and works fine again. Hopefully next time someone will tell me how to get that old screw out faster.

I went ahead with the repair after reading how easy it was. I located the wires which were spliced, held together with wire nuts and wrapped in black insulation tape which did not feel right. Not realizing that these were ceramic heat resistant wire nuts and not wanting to cut the connector off the new ignitor I tried in vain to find a way to disconnect the original from it's source. In vain I searched for a way to reach where it plugged in. Looking for diagrams on line I came across one mention of: when you can't reach where to unplug the connector splice the wires using the heat resistant wire nuts. Encouraged I did that without the black insulation tape and then tried to slide the ignitor into the protective housing. The filament broke! I was devastated. Out $50.00 plus ego deflated I called PartSelect and bless their soul they sent me a new one under warranty. I didn't even have to ask for it. Their turn around time was the same as before and within two days not counting the weekend the oven lit like a Christmas candle. Thanks to all before me who shared their experience. Curious though why no one mentioned the splicing method.

PriceSelect was the best. Special thanks to them.

order new ones, got the model#, also thanks too my husband he look on line and found your company thank you so much. i will tell my family, and friends about your company thank you again great job. lisa

Unscrewed the burners,lifted the top up,unplugged the burners.Took out the bad module,making sure of where the wires went and put them in the same spots on the new module,reconnected the burners lowered the top screwed the burners back in and the burners lit.

My husband took the oven door off then the bottom piece below the shelf took the old ignigter out put the new on in and now I have an oven again.

1. Removed drawer
2.Removed back panel (2 screws).
3. Disconnected power line from old igniter
4. Removed 3 screws holding old igniter.
5. Replaced with new igniter.
Works like new.

Replaced the existing ignitor by removing the bottom drip pan/gas line/ignitor (apprimately 18 screws), unscrewing the wire nuts, removing the old ignitor, connecting the wires to the new ignitor, and reinstalling the drip pan/gas line/ignitor (18 screws).

Removed the top, 4 screws and pulled the contact wires off. Replaced the module and connected the contacts. Put back the screws and the top. When the stove was new it did not operate properly and we had a technician out, but naturally it worked for him. For the past 14 years intermittent operation has been agravating me. With the new module the burners have never worked so well.