Quick Question!

Have you ever purchased from PartSelect.com before?

Models > ARB9059CS (PARB9059CS0) > Instructions

ARB9059CS (PARB9059CS0) Amana Refrigerator - Instructions

All installation instructions for ARB9059CS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the ARB9059CS
511-525 of 677
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

ice maker

  • Customer: Rozell from Cleveland, MS
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 0 of 0 people found this instruction helpful
well, my problem was the dual water valve. I check the two water valve connectors, one was good ( yellow ) and the other connector (brown) was bad. I tested them both with an ohms meter, of course all power was off. I think when ever there's a problem with not receiving ICE this should be done before replacing the ice-maker for there's a lot of things going on in this area. The Brown Connector releases the water into the ice-tray (that tested Bad with a reading of 257 from ohms meter,and the yellow had a sound from ohms for full contact a good reading. The brown valve was bad.

Screws on the door of the dishwasher were very loose.

  • Customer: Kathryn from Carol Stream, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Went to PartsSelect. Put in Dishwasher model number. Chose the screws for that model number. Ordered the screws. Can't get any easier than that!

broken pin on left end cap

  • Customer: marilou from clyde hill, WA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
piece of cake to repair - great instructions!!

Automatic ice maker was not working properly

  • Customer: Donna from Tucson, AZ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
We had an Appliance Repair service come to fix, and they replaced the ice maker and the water valve, but ice maker was still not performing properly. We use RO water to fill the ice maker and because the water was also going through the charcoal cartridge, there wasn't enough water pressure to completely fill the tray. Plus charcoal filter was probably clogged. The original Blue Bypass Cap was nowhere to be found and I even called Kitchenaid to get one. They were of no help. But found your site, and found the part I needed. And best of all, ice maker is not jamming and is now making real ice cubes, not hollow, thin ones. And the water dispenser is now working too, so am very happy that such a small thing, fixed the big problem. Who knows, a clogged charcoal filter may have been the whole problem from the start.

Broken plastic molding on cheese drawer end cap prevented cover from operating properly

  • Customer: Peter from East Falmouth, MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I removed the end cap from the refrigerator by taking out three phillips head screws. Two additional screws were removed to demount the drawer track and remount it on the new molding. The new molding was re-attached to the refrigerator wall and now the cheese drawer has a functional cover. Very easy.

Fridge section too warm and freezer cold

  • Customer: Sheila from Folsom, LA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The unit has two fans on it. One is located in the back and the other is locate inside the freezer section behind the panel. Remove the four bolts holding the door to the sliding rack. Remove the ice machine. Remove the back panel. Noticed that the fan was covered in ice thus shorting the fan motor. Tested for voltage to the fan was good. Replaced evaporator fan motor and unit works perfectly

The Ice and water filter was old. Had to replace.

  • Customer: Debora from Avon, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I unscrewed the old filter and screwed the new filter in the way the instructions said. I have done this before with no problems. Easy fix.

frig not cooling kicking in and out

  • Customer: ronald from warren, OH
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
unplugged and plugged in new capacitor and overload relay.frig works like new.Took old relay apart and it was fried. Thanks for the parts and the help.

needed new water filter

  • Customer: Patricia from Huntsville, AL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Screwed new filter in

Ice maker pouring water into icebucket

  • Customer: Grant from Cary, NC
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Watching the video made this dead easy. If I had a newer refrigerator, I suspect it would have taken 10 minutes. Since I have an older 'fridge, I ran into two issues not in the PartSelect video. First - there were no "clips" to slip the icemaker into/out of, the unit was screwed directly into the freezer wall. Kinda hard to see the screws, especially the one in front, but not a big problem. Second - there is a wire-harness clip at the back side of the icemaker, that hooks onto the ledge of the back connector, just under the screw. That clip had slipped, and until I figured that out and reseated it, it made getting to the rear screw wit the nutdriver a serious pain. Other than those two issues, though, the job was exactly as easy as the video makes it look!

Water leaking into bin

  • Customer: Charles from Fort Myers, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Cubes in bin were freezing together due to water leaking from the ice maker assembly. Replacement went easy with bin rails removed.

ice maker leaking the covering was coming off the tray

  • Customer: Curtis from Frisco, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1. removed bottom screw. 2. pinched sides of rear connection to disconnected ice maker (noted red wire on top in cabinet rear). 3. bump out old unit taping to release tab on bottom. 4. disconnect wire from icemaker and remove wire holder with philips screwdriver.ew ice maker. 4. reattach harness to new ice make and replace clip. 6 reattach l bracket to bottom of ice maker. 7. detach shut off wire from old ice maker and replace on the new maker. 8. place back into position in freezer compartment. 9. reattach water delivery tube 10. connect wire to rear of cabinet. If motor drive still good on old maker scavenge before throwing away bad parts.

broken water fill cup

  • Customer: augustine from cedar rapids, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
empty frezzer take door off unplug wires going to ice maker unscrew/bolt icemaker replace door take motor cover off ice maker remove screws on motor replace ice cup and put every thing back together

Freezer section icing up, getting too cold, refrigerator getting too warm.

  • Customer: Cecil from Carmel Valley, CA
  • Difficulty: Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Local appliance repair co. diagnosed and replaced motorized door in refrigerator section; problem manifested itself again one week later. Same appliance repair co. then said it was probably the defrost thermostat, they changed thermostat; problem came back after another week. I went on your site and figured that the next most likely thing was the defrost heater. I ordered one and it came the next day. I dismantled the various panels, sensor covers, air dams and removed and replaced the heater element. After watching the refrigeration cycle for a couple of days I saw that the problem appeared to be cured then I replaced the panel and sensor and fan covers and put the ice cream back in. That was a week ago, it seems to be ok now.

Ice maker was leaking water and freezing the ice in the trray

  • Customer: DeVerl from orem, UT
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I unplugged the refrigerator. Then removed the ice tray. Then removed the screw holding the ice maker secure. I had a little difficulty lifting the ice maker off the clips on the side of the refrigerator but was successful. Then unplugged the wire harness from the back of the refrigerator an lifted the unit out. Removed the wiring harness from the old unit and installed it on the new one. Then positioned the new unit so I could plug the harness in the refrigerator and lined up the clips to attach it on the side of the refrigerator, being careful to line up the water distribution tube. Replaced the screw to secure the ice maker and plugged the refrigerator back in and it is working very well. I am very hsappy with the repair
All Instructions for the ARB9059CS
511-525 of 677